Complete Okuma Mill G and M Codes list for cnc machinists who work on Okuma cnc milling machines.
Okuma Mill OSP-P200M
Okuma Mill G Codes
| G Code | Description |
|---|---|
| G00 | Positioning |
| G01 | Linear interpolation |
| G02 | Circular interpolation – Helical cutting (CW) |
| G03 | Circular interpolation – Helical Cutting (CCW) |
| G04 | Dwell |
| G09 | Exact stop |
| G10 | Cancel of G11 |
| G11 | Parallel and rotational shift of coordinate system |
| G14 | Designation of axis name |
| G15 | Selection of work coordinate system (Modal) |
| G16 | Selection of work coordinate system (One-shot) |
| G17 | Plane selection: XY |
| G18 | Plane selection: ZX |
| G19 | Plane selection: YZ |
| G20 | Inch input confirmation |
| G21 | Metric input confirmation |
| G22 | Programmable stroke limit ON |
| G23 | Programmable stroke limit cancel |
| G30 | Positioning to home position |
| G31 | Skip function |
| G33 | Unfixed cycle for thread cutting |
| G37 | Cancel of G38 |
| G38 | Air cut reduction mode ON |
| G39 | I, J, K commands and G39 ignored in the corner circular interpolation (with vector) |
| G40 | Cutter radius compensation (G41, G42) cancel |
| G41 | Cutter radius compensation, left |
| G42 | Cutter radius compensation, right |
| G43 | 3D offset (G44) cancel |
| G44 | 3D offset ON |
| G50 | Enlargement and reduction of geometry cancel |
| G51 | Enlargement and reduction of geometry “ON” |
| G53 | Tool length offset cancel |
| G54 | Tool length offset, X-axis |
| G55 | Tool length offset, Y-axis |
| G56 | Tool length offset, Z-axis |
| G57 | Tool length offset, 4th-axis |
| G58 | Tool length offset, 5th-axis |
| G59 | Tool length offset, 6th-axis |
| G60 | One-directional positioning |
| G61 | Exact stop mode ON |
| G62 | Programmable mirror image mode |
| G64 | Cutting mode ON |
| G68 | Slope coordinate OFF |
| G69 | Slope coordinate ON |
| G71 | Designation of return level for M53 |
| G72 | Designation of pattern reference point (start position) for the coordinate calculation function |
| G73 | Fixed cycle, High speed drilling cycle |
| G74 | Fixed cycle, Reverse tapping cycle |
| G75 | Fixed cycle; Step & pick cycle |
| G76 | Fixed cycle, Fine boring |
| G79 | Fixed cycle; Variable pitch cycle |
| G80 | Fixed cycle, Modal cancel |
| G81 | Fixed cycle; Spot boring |
| G82 | Fixed cycle; Counter boring |
| G83 | Fixed cycle, Deep hole drilling cycle |
| G84 | Fixed cycle, Tapping cycle |
| G85 | Fixed cycle, Boring cycle |
| G86 | Fixed cycle, Boring cycle |
| G87 | Fixed cycle, Back boring cycle |
| G88 | Fixed cycle; Multi-step boring cycle |
| G89 | Fixed cycle, Boring cycle |
| G90 | Absolute dimensioning mode |
| G91 | Incremental dimensioning mode |
| G92 | Setting of work coordinate system |
| G93 | Inverse time feed |
| G94 | Feed per minute mode |
| G95 | Feed per revolution mode |
| G96 | Local coordinate system setting |
| G97 | Coordinate recalculation function |
| G100 | Cancel of macro MODIN mode selected by G101 to G110 |
| G101-G110 | G code macro MODIN type |
| G111-G120 | G code macro CALL type |
| G130 | High-speed contouring control OFF |
| G131 | High-speed contouring control ON |
| G133 | Constant peripheral speed control OFF |
| G134 | Constant peripheral speed control ON |
| G137 | Contour machining mode OFF |
| G138 | Contour machining mode ON |
| G139 | G00 special linear interpolation OFF |
| G140 | G00 special linear interpolation ON |
| G141 | Tool grooving OFF |
| G142 | Tool grooving ON |
| G143 | Rotary axis position command (under rotary axis control by Super hi-NC) |
| G145 | Pattern reference point return mode |
| G146 | Pattern end point return mode |
| G147 | Machine coordinate system position command |
| G148 | Turning cut function OFF |
| G149 | Turning cut function ON |
| G150 | Auto acceleration/deceleration ON |
| G151 | Auto acceleration/deceleration cancel |
| G152 | Auto acceleration |
| G153 | Auto deceleration |
| G154 | Spindle path control OFF |
| G155 | Spindle path control ON |
| G159 | In-position check disabling command |
| G164 | Continuous circular movement stop command in turning cut |
| G165 | Continuous circular movement (CW) start command in turning cut |
| G166 | Continuous circular movement (CCW) start command in turning cut |
| G167 | Rotary table and spindle control OFF |
| G168 | Rotary table and spindle control ON |
| G169 | Tool length offset at cutting edge ON |
| G170 | Tool length offset at cutting edge and in axial direction cancel |
| G171 | Tool length offset in axial direction ON |
| G174 | Cylindrical side cutting “OFF” |
| G175 | Cylindrical side cutting “ON” |
| G176 | F, S codes ignore cancel |
| G177 | F, S codes ignore |
| G178 | Fixed thread cutting cycle in the 1st axis direction on a plane |
| G179 | Fixed thread cutting cycle in the 2nd axis direction on a plane |
| G180 | Attachment rotation offset cancel |
| G181 | Attachment rotation offset; Frontward |
| G182 | Attachment rotation offset; Leftward |
| G183 | Attachment rotation offset; Backward |
| G184 | Attachment rotation offset; Rightward |
| G185 | Attachment rotation offset; Downward |
| G186 | Tolerance control mode cancel |
| G187 | Tolerance control mode “ON” |
| G188 | 2nd tool length offset cancel |
| G189 | 2nd tool length offset ON |
| G192 | Fixed cycle; Upper surface detection cancel |
| G193 | Fixed cycle; Upper surface detection ON |
| G194 | Fixed cycle; Tool breakage detection cancel |
| G195 | Fixed cycle; Tool breakage detection ON |
| G260 | Spindle deflection compensation OFF |
| G261 | Spindle deflection compensation ON |
| G266 | Limit switch checked |
| G267 | Limit switch not checked |
| G272 | Fixed cycle; Deep hole tapping and reverse tapping |
| G273 | Fixed cycle; High-speed deep hole tapping and reverse tapping |
| G274 | Fixed cycle; Synchronized tapping, reverse tapping |
| G281 | Fixed cycle; Small diameter and deep hole drilling |
| G282 | Fixed cycle; Deep hole synchronized tapping |
| G283 | Fixed cycle; High-speed deep hole synchronized tapping |
| G284 | Fixed cycle; Synchronized tapping |
| G296 | G297 cancel |
| G297 | S command in C-axis mode (S command is regarded as the spindle position.) |
| G300 | G301 to G349 macro MODIN cancel (NC. P. B No. 34 bit 3:1) |
| G336 | I-MAP-A function; Fixed circle cutting cycle (CW) |
| G337 | I-MAP-A function; Fixed circle cutting cycle (CCW) |
| G501-G580 | G code macro changeable between MODIN and CALL |
Okuma Mill M Codes
| M Code | Description |
|---|---|
| M00 | Program stop |
| M01 | Optional stop |
| M02 | End of program |
| M03 | Work spindle start (CW) |
| M04 | Work spindle start (CCW) |
| M05 | Spindle stop |
| M06 | Vertical spindle tool change |
| M07 | Oil mist coolant ON |
| M08 | Coolant pump ON |
| M09 | Coolant system OFF |
| M10 | A-axis clamp |
| M11 | A-axis unclamp |
| M12 | Chip air blow ON |
| M15 | 4th-axis rotary index table CW |
| M16 | 4th-axis rotary index table CCW |
| M17 | Indexing head index CCW |
| M19 | Spindle orientation (forward) |
| M20 | B-axis clamp |
| M21 | B-axis unclamp |
| M22 | Y-axis clamp |
| M23 | Y-axis unclamp |
| M24 | Z-axis clamp |
| M25 | Z-axis unclamp |
| M26 | C-axis clamp |
| M27 | C-axis unclamp |
| M30 | End of tape |
| M32 | Splash guard door close |
| M33 | Splash guard door open |
| M40 | High/middle-high/middle-low/low range |
| M41 | High/middle-high/middle-low range |
| M42 | High/middle-high range |
| M43 | High range |
| M44 | AAC (F) 1 Next attachment clear |
| M45 | AAC (F) 1 Preparation for attachment change preparation |
| M46 | AAC (F) 1 No next attachment |
| M47 | AAC (F) 1 No next attachment |
| M48 | AAC (T) Next attachment clear |
| M49 | AAC (T) Preparation for attachment change preparation |
| M50 | Through-the-tool coolant, low pressure ON |
| M51 | Through-the-tool coolant, high pressure ON |
| M52 | Return level in fixed cycle, Upper limit |
| M53 | Return level in fixed cycle, Specified level |
| M54 | Return level in fixed cycle, Point R level |
| M57 | W-axis clamp |
| M58 | W-axis unclamp |
| M59 | Chip air blow ON |
| M60 | Pallet change command |
| M62 | Vertical spindle tool change preparation |
| M63 | No next tool for ATC |
| M64 | Next tool return cycle |
| M65 | ATC preparation |
| M66 | Continuous tool change between the vertical and horizontal spindles (same tool) |
| M67 | Continuous tool change between the vertical and horizontal spindles (different tool) |
| M68 | Vertical spindle tool clamp |
| M69 | Vertical spindle tool unclamp |
| M70 | Manual tool change |
| M71 | Manual attachment tool change |
| M72 | Horizontal spindle tool change preparation |
| M73 | Swivel head, front position |
| M74 | Swivel head, left position |
| M75 | Swivel head, rear position |
| M76 | Swivel head, right position |
| M77 | Horizontal spindle tool change |
| M78 | Horizontal spindle tool clamp |
| M79 | Horizontal spindle tool unclamp |
| M81 | Automatic W-axis positioning 1 |
| M82 | Automatic W-axis positioning 2 |
| M83 | Automatic W-axis positioning 3 |
| M84 | Automatic W-axis positioning 4 |
| M85 | Automatic W-axis positioning 5 |
| M87 | Oil mist/air blow ON |
| M87 | Oil mist/air blow ON |
| M88 | Dust collector ON |
| M89 | Dust collector OFF |
| M90 | Vertical spindle oil mist cycle mode ON |
| M91 | Tap-drill hole chip air blow cycle mode ON |
| M93 | Thru-spindle coolant at medium pressure/2nd coolant ON |
| M94 | Attachment indexing by forward rotation |
| M95 | Attachment indexing by reverse rotation |
| M98 | Horizontal spindle oil mist cycle mode ON |
| M101 | Pallet 1 selection |
| M102 | Pallet 2 selection |
| M103 | Pallet 3 selection |
| M104 | Pallet 4 selection |
| M105 | Pallet 5 selection |
| M106 | Pallet 6 selection |
| M107 | Pallet 7 selection |
| M108 | Pallet 8 selection |
| M109 | Pallet 9 selection |
| M110 | Pallet 10 selection |
| M111 | Pallet 11 selection |
| M112 | Pallet 12 selection |
| M115 | 5th-axis rotary table CW |
| M116 | 5th-axis rotary table CCW |
| M118 | Spindle orientation (reverse) |
| M119 | Spindle orientation (forward/reverse) |
| M120 | Work shower ON |
| M121 | Attachment air blow ON/Tool nose air blow ON |
| M127 | Touch probe ON |
| M130 | Spindle rotation condition for cutting feed OFF |
| M131 | Spindle rotation condition for cutting feed ON |
| M132 | Single block invalid |
| M133 | Single block valid |
| M134 | Spindle speed override invalid |
| M135 | Spindle speed override valid |
| M136 | Feedrate override invalid |
| M137 | Feedrate override valid |
| M138 | Dry run invalid |
| M139 | Dry run valid |
| M140 | Slide hold invalid |
| M141 | Slide hold valid |
| M142 | Spindle overload detection invalid |
| M143 | Spindle overload detection valid |
| M144 | Touch sensor advance |
| M145 | Touch sensor retract |
| M146 | Work air blow OFF |
| M147 | Work air blow ON |
| M148 | Work clamp (fixture 1) |
| M149 | Work unclamp (fixture 1) |
| M150 | Coolant group specification, Vertical spindle |
| M151 | Coolant group specification, Horizontal spindle |
| M152 | Coolant group specification, 3rd group |
| M153 | Coolant group specification, 4th group |
| M154 | Sensor air blow OFF |
| M155 | Sensor air blow ON |
| M157 | AAC (2 st.), No next tool |
| M158 | AAC (2 st.), Next tool clear |
| M159 | AAC (2 st.), Preparation for the next tool |
| M160 | PPC pallet loading |
| M161 | PPC pallet unloading |
| M163 | Long tool, No next tool |
| M165 | Long tool, Preparation for tool change |
| M166 | ATC active tool return mode specification |
| M170 | AAC (F), Attachment change |
| M171 | AAC (T), Attachment change |
| M172 | Long tool, Tool change command |
| M173 | AAC (2 st.), Attachment change command |
| M176 | Dust collection mode, Air blow |
| M177 | Angular attachment, Tool change |
| M178 | Dust collection mode, ON |
| M179 | Dust collection mode, OFF |
| M181 | External M signal |
| M182 | External M signal |
| M183 | External M signal |
| M184 | External M signal |
| M185 | External M signal |
| M186 | External M signal |
| M187 | External M signal |
| M188 | External M signal |
| M190 | Automatic W-axis positioning 1 |
| M191 | Automatic W-axis positioning 2 |
| M192 | Automatic W-axis positioning 3 |
| M193 | Automatic W-axis positioning 4 |
| M194 | Automatic W-axis positioning 5 |
| M195 | Automatic W-axis positioning 6 |
| M196 | Automatic W-axis positioning 7 |
| M197 | Automatic W-axis positioning 8 |
| M198 | Automatic W-axis positioning 9 |
| M199 | Automatic W-axis positioning 10 |
| M201-M220 | M code macro |
| M230 | Tool length offset direction; Used as it is |
| M231 | Tool length offset direction; Used after reversing the direction |
| M232 | 3D tool length offset direction; Used as it is |
| M233 | 3D tool length offset direction; Reversed and used |
| M234 | Synchronized tapping gear selection: Low, Middle low, Middle high, High |
| M235 | Synchronized tapping gear selection: Middle low, Middle high, High |
| M236 | Synchronized tapping gear selection: Middle high, High |
| M237 | Synchronized tapping gear selection: Middle high, High |
| M238 | Software override invalid |
| M239 | Software override valid |
| M278 | Chip conveyor OFF |
| M279 | Chip conveyor ON |
| M280 | Work counter count up |
| M281 | Work clamp (fixture 2) |
| M282 | Work unclamp (fixture 2) |
| M287 | Work clamp (fixture 3) |
| M288 | Work unclamp (fixture 3) |
| M289 | Pallet identification |
| M292 | Chamfering OFF |
| M293 | Chamfering ON |
| M294 | Fixed compound cycle; Cutting pattern 1 |
| M295 | Fixed compound cycle; Cutting pattern 2 |
| M296 | Fixed compound cycle; Cutting pattern 3 |
| M297 | Thermal deformation amount transfer command |
| M300 | Ignoring Spindle rotation answer |
| M301 | Ignoring M code answer other than spindle rotation |
| M302 | M301 answer confirmation |
| M311 | Robot request 1 |
| M312 | Robot request 2 |
| M313 | Robot request 3 |
| M314 | Robot request 4 |
| M315 | U-axis connection OFF |
| M316 | U-axis connection ON |
| M317 | U-axis air blow OFF |
| M318 | U-axis air blow ON |
| M319 | Operation time transfer command (DNC-C) |
| M320 | Tailstock advance |
| M321 | Tailstock retract |
| M326 | Synchronized tapping monitor OFF |
| M327 | Synchronized tapping monitor ON |
| M328 | Spindle no-tool interlock valid |
| M329 | Spindle no-tool interlock invalid |
| M331 | 6th rotary axis CW |
| M332 | 6th rotary axis CCW |
| M339 | Thru-spindle air blow ON |
| M340 | Work seating monitor ON |
| M341 | Work seating monitor OFF |
| M342 | Work seating confirmation air ON |
| M343 | Work seating confirmation air OFF |
| M346 | B-axis rotation interlock valid |
| M347 | B-axis rotation interlock invalid |
| M351 | AT retraction to MG upper part (MCV-A II simplified 5-face MC) |
| M352 | Adaptor retraction to MG upper part (MCV-A II simplified 5-face MC) |
| M354 | Chip flusher OFF |
| M355 | Chip flusher ON |
| M356 | MG pot swing to tool change position |
| M368 | Mist collector OFF |
| M369 | Mist collector ON |
| M374 | Non-contact sensor; Laser OFF |
| M375 | Non-contact sensor; Laser ON |
| M378 | Coolant flow rate detection; Monitor mode ON |
| M379 | Coolant flow rate detection; Monitor mode OFF |
| M385 | Work clamp at low pressure (fixture 1) |
