Selca G13 Straight line, at a known angle, through a point or tangent to a circle
Contents
G13 X... Y... [I...] J... [K...]
| Parameter | Description |
|---|---|
| X,Y | Point or circle center coordinates. |
| I | Radius of the circle of tangency (omitted if it is a point). |
| J | Angle between straight line and X-axis. |
| K | Selects one of the intersections between the straight line and the circle programmed in the previous block. |
Selca G11 Second point or Circle that defines a straight line ContentsProgrammingParameters Programming G11 X… Y… [I… K…] Parameters Parameter Description X,Y Circle center or supporting point coordinates. I Circle…
Selca G10 First point or circle that defines a straight line ContentsProgrammingParameters Programming G10 X… Y… [I…] Parameters Parameter Description X,Y Circle center or supporting point coordinates. I Circle radius…
Selca G20 Circle of known center and radius ContentsProgrammingParameters Programming G20 [X… Y…] [I…] [K…] Parameters Parameter Description X,Y Circle center coordinates. May be omitted if coinciding with the center…
CNC G01 A… Angle Programming When using G1 (G01) G-code instructions as well as the end of movement co-ordinates X and/or Z, besides radii (G01 R…) or chamfers (G01 C…)…
Selca G40 Exit from profile and cutter compensation disable ContentsProgrammingParameters Programming G40 [K…] [X… Y…] Parameters Parameter Description K selects profile exit mode: K1: automatic profile exit with a straight…
[G13 Straight line, at a known angle, [ through a point or tangent to a circle [G20 Circle of known center and radius [G21 Linking radius [G51 Offset / rotation…
G70 Bolt Hole Circle G-Code (canned cycle) is very simple to program due to its small number of parameters. G70 bolt hole circle parameters are very self explanatory, but this…
Selca G42 Enables tool radius compensation, tool right of profile ContentsProgrammingParameters Programming G42 [K…] [I1] [Q…] [D0=1] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Selca G41 Enables tool radius compensation, tool left of profile ContentsProgrammingParameters Programming G41 [K…] [I1] [Q…] [D0=…] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Want to drill or tap in a circle, but you only know the radius of the circle and number of the holes. Then don’t worry G70 Bolt Hole Circle will…
/*Parameters G65 P9100 Xx Yy Zz Rr Ff Ii Aa Bb Hh X: X coordinate of the center of the circle (#24) Y: Y coordinate of the center of the…
G70 Bolt Hole Circle command makes it easy to drill/tap/bore in a circle at even distances. There is no need to know or calculate each hole position. You just are…
ContentsSinumerik HOLES2 Hole CircleProgrammingParameters Sinumerik HOLES2 Hole Circle With Sinumerik HOLES2 cycle, a hole circle can be machined (BHC). Programming HOLES2 (CPA, CPO, RAD, STA1, INDA, NUM) Parameters Parameter Description…
G72 Bolt Holes Along an Angle command makes it easy for a cnc machinists to Drill/Bore/Tap evenly spaced holes along an angle. G72 is non-modal G-code. G72 Bolt Holes Along…
Selca G62 Type of coordinates for the definition of circle center in G2/G3 ContentsProgrammingParameters Programming G62 K… Parameters Parameter Description K type of coordinates. K1 absolute coordinates. K2 incremental coordinates,…
Selca G774 Roll-Over rotary axes (only for S4000 Series CNCs) ContentsProgrammingParameters Programming G774 [A] [B] [C] [D0=…] [D1=…] Parameters Parameter Description A, B,C name of the rotary axis where to…
Selca G75 G76 Polar coordinate programming ContentsG75 Cancels G76ProgrammingG76 Polar coordinate programmingProgrammingParameters G75 Cancels G76 G75 Cartesian coordinate programming (cancels G76) Programming G75 [X…] [Y…] [Z…] Enabled: (default) until a G76…
ContentsSinumerik ANG=ANG= Example Sinumerik ANG= If the end points for the contour are not directly specified in the machining drawing, it is also possible to use an angle specification ANG=……
As with G70 Bolt Hole Circle a cnc machinists can machine drills/tap/bore evenly spaced holes in a circle, the same way sometimes you have to drill/tap/bore evenly spaced holes in…
Selca G787 Grid pattern machining repeat supercycle ContentsProgrammingParameters Programming G787 X… Y… [D1=…] [D2=…] [D3=…] [D4=…] [D5=…] [D6=…] [D7=…] Parameters Parameter Description X,Y starting point coordinates. D1= number of figures…
