Selca G94 F-feed rate in mm/min or inches/min

Selca G95 F-feed rate in mm/rev or inches/rev ContentsProgrammingParameters Programming G95 F… Parameters Parameter Description F new feed rate. Enabled: until a G92 or a G93 G94 G95 with new…

Selca G92 F-feed rate override ContentsProgrammingParameters Programming G92 F Parameters Parameter Description F the new feed rate overrides all F functions programmed in the subsequent blocks. Enabled: until a G92 or…

Selca G93 Feed rate defined as inverse of block execution time ContentsProgrammingParameters Programming G93 F… Parameters Parameter Description F new feed rate. Enabled: until a G92 or a G93 G94…

Selca G30 G31 Continuous motion mode with automatic feed adjustment ContentsG30 Cancels G31ProgrammingG31 Continuous motion modeProgrammingParameters G30 Cancels G31 G30 Cancels G31 and re-establishes deceleration at block end Programming G30…

Selca G872 ON /OFF touch probe measuring cycle in space ContentsProgrammingParameters Programming G872 [X…] [Y…] [Z…] [I…] [F…] [R] Parameters Parameter Description X,Y,Z expected coordinates of the point to be…

Selca G873 Touch /copying probe measuring cycle in space ContentsProgrammingParameters Programming G873 [X…] [Y…] [Z…] [I…] [F…] [R] Parameters Parameter Description X,Y,Z expected coordinates of the point to be measured….

Selca G85 Reaming fixed cycle ContentsProgrammingParameters Programming G85 [X… Y…] Z… I… [Q…] [K…] [F…] [D8=…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane. J hole starting…

Selca G760 G761 Axis travel delimitation ContentsG760 Cancels G761ProgrammingG761 Axis travel delimitationProgrammingParameters G760 Cancels G761 G760 Cancels G761 Programming G760 G761 Axis travel delimitation G761 Axis travel delimitation Programming G761…

Selca G60 G61 Scaling factor ContentsG60 Cancels G61ProgrammingG61 Scaling factorProgrammingParametersG61 Programmable zone scalingProgrammingParameters G60 Cancels G61 G60 Cancels G61 (scaling factor) Programming G60 G61 Scaling factor G61 Scaling factor Programming…

Selca G88 Spaced plane drilling fixed cycle ContentsProgrammingParameters Programming G88 [X… Y…] Z… J… [K…] [F…] [D8=…] Parameters Parameter Description X,Y hole coordinates. Z first wall depth. J drilling starting…

Selca G83 Deep drilling fixed cycle with tool retraction for chip discharge ContentsProgrammingParameters Programming G83 [X… Y…] Z… J… I… [Q…] [K…] [F…] [D0=…] [D7=1] [D8=…] [D9=1] Parameters Parameter Description…

Selca G81 Drilling /spot facing fixed cycle ContentsProgrammingParameters Programming G81 [X… Y…] Z… [I…] J… [Q…] [K…] [F…] [D8=…] [D9=1] [D10=…] [D11=…] [D13=…] Parameters Parameter Description X,Y hole coordinates. Z…

Selca G730 G731 High speed milling of profiles defined by points ContentsG730 Cancels G731ProgrammingG731 High speed milling of profiles defined by pointsProgrammingParameters G730 Cancels G731 G730 Cancels G731 (Only for…

Selca G75 G76 Polar coordinate programming ContentsG75 Cancels G76ProgrammingG76 Polar coordinate programmingProgrammingParameters G75 Cancels G76 G75 Cartesian coordinate programming (cancels G76) Programming G75 [X…] [Y…] [Z…] Enabled: (default) until a G76…

Selca G67 G68 G69 Static TCPM ContentsG67 Cancels G68/G69ProgrammingG68 Static TCPM for rotary tablesProgrammingParametersG69 Static TCPM for rotary headsProgrammingParameters G67 Cancels G68/G69 G67 Cancels G68/G69 static TCPM Programming G67 G68…

Selca G82 Deep mixed drilling cycle ContentsProgrammingParameters Programming G82 [X… Y…] Z… I… J… [Q…] [K…] [F…] [D0=…] [D7=1] [D8=…] [D9=1] [D10=…] [D11=…] [D12=…] [D13=…] [D14=…] Parameters Parameter Description X,Y…

Selca G86 Boring fixed cycle ContentsProgrammingParameters Programming G86 [X… Y…] Z… J… [Q…] [K…] [I…] [F…] [D0=…] [D7=…] [D8=…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane….

Selca G84 Tapping fixed cycle ContentsProgrammingParameters Programming G84 [X… Y…] Z… J… F… [I…] [Q…] [K…] [D8…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane. J hole…

Feed Per Revolution (G95) G95 (Feed Per Revolution) is a modal G-code that instructs the control to interpret feed commands as mm per revolution (mm/rev) or inches per revolution of the spindle. G01 F0.02…

Selca G17 G18 G19 Plane selection ContentsG17 Plane selection XYProgrammingG17 Selection of planes different than XYProgrammingParametersG18 Plane selection ZXProgrammingG19 Plane selection YZProgramming G17 Plane selection XY G17 Plane selection (XY…