Selca G817 Tool length offset on an axis non-orthogonal to the machining plane
Contents
G817 Axis
| Parameter | Description |
|---|---|
| Axis | name of the machine axis to which the compensation is to be applied. |
Enabled: until cycle / program end.
Selca G50 G51 Offset / rotation of the coordinate system on the plane ContentsG50 Cancels the offset/rotationProgrammingG51 Offset / rotationProgrammingParameters G50 Cancels the offset/rotation G50 Cancels the offset / rotation…
Selca G48 Recalls and enables tool length compensation ContentsProgrammingParameters Programming G48 [K…] [I…] Parameters Parameter Description K compensation number. I finish stock value. Note: program G48 I0 to disable the…
ContentsG43 Tool Length Compensation positiveProgrammingExampleG44 Tool Length Compensation negativeProgrammingG49 Cancel Tool Length CompensationProgramming G43 Tool Length Compensation positive With G43 a value from the offset register (OFFSET) can be called…
Selca G52 Offset of the coordinate system on the plane ContentsProgrammingParameters Programming G52 [X…] [Y…] [Z…] [I] Parameters Parameter Description X, Y, Z coordinates of the new origin with respect…
Selca G88 Spaced plane drilling fixed cycle ContentsProgrammingParameters Programming G88 [X… Y…] Z… J… [K…] [F…] [D8=…] Parameters Parameter Description X,Y hole coordinates. Z first wall depth. J drilling starting…
Selca G17 G18 G19 Plane selection ContentsG17 Plane selection XYProgrammingG17 Selection of planes different than XYProgrammingParametersG18 Plane selection ZXProgrammingG19 Plane selection YZProgramming G17 Plane selection XY G17 Plane selection (XY…
Selca G83 Deep drilling fixed cycle with tool retraction for chip discharge ContentsProgrammingParameters Programming G83 [X… Y…] Z… J… I… [Q…] [K…] [F…] [D0=…] [D7=1] [D8=…] [D9=1] Parameters Parameter Description…
Selca G736 Surfaces defined by a plane profile and one or more section profiles: plane profile and parameters ContentsProgrammingParameters Programming G736 I… [X… Y…] [J…] [K…] [Q…] [D0=…] [D1=…] [D2=…]…
Selca G740 G746 G748 G749 4-axis surface machining ContentsG740 Cancels G748 and G749ProgrammingG746 Defers G748 cycleProgrammingG748 4-axis surface machiningProgrammingParametersG749 4-axis surface machiningProgrammingParameters G740 Cancels G748 and G749 G740 Cancels G748…
Selca G85 Reaming fixed cycle ContentsProgrammingParameters Programming G85 [X… Y…] Z… I… [Q…] [K…] [F…] [D8=…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane. J hole starting…
Selca G84 Tapping fixed cycle ContentsProgrammingParameters Programming G84 [X… Y…] Z… J… F… [I…] [Q…] [K…] [D8…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane. J hole…
Selca G60 G61 Scaling factor ContentsG60 Cancels G61ProgrammingG61 Scaling factorProgrammingParametersG61 Programmable zone scalingProgrammingParameters G60 Cancels G61 G60 Cancels G61 (scaling factor) Programming G60 G61 Scaling factor G61 Scaling factor Programming…
Selca G42 Enables tool radius compensation, tool right of profile ContentsProgrammingParameters Programming G42 [K…] [I1] [Q…] [D0=1] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Selca G41 Enables tool radius compensation, tool left of profile ContentsProgrammingParameters Programming G41 [K…] [I1] [Q…] [D0=…] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Manual operation in which a reference tool and the tool to be measured are pressed against a fixed point on the machine, one after the other, and the difference in length between…
Selca G850 G851 Part origin offset by handwheels ContentsG850 Cancels G851ProgrammingG851 Part origin offset by handwheelsProgrammingParameters G850 Cancels G851 G850 Cancels G851 Programming G850 Enabled: only in the block in…
Selca G86 Boring fixed cycle ContentsProgrammingParameters Programming G86 [X… Y…] Z… J… [Q…] [K…] [I…] [F…] [D0=…] [D7=…] [D8=…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane….
Selca G840 G841 Tool radius compensation in space ContentsG840 Cancels G841ProgrammingG841 Tool radius compensation in spaceProgrammingParameters G840 Cancels G841 G840 Cancels G841 Programming G840 G841 Tool radius compensation in space…
ContentsFanuc G17 G18 G19 Plane SelectionG17 XY-PlaneProgrammingG18 ZX-PlaneProgrammingG19 YZ-PlaneProgramming Fanuc G17 G18 G19 Plane Selection With G17 G18 G19 the plane will be defined, in which circular interpolation and polar…
Selca G845 G846 Manual axis control by handwheels during machining ContentsG845 Cancels G846ProgrammingG846 Manual axis control by handwheels during machiningProgrammingParameters G845 Cancels G846 G845 Cancels G846 Programming G845 Enabled: only…
