Fanuc Alarms

Fanuc Alarm PS898 ILLEGAL PARAMETER IN G54.2 Fanuc Alarm Description Fanuc 15/15i An illegal parameter (Nos. 6068 to 6076) was specified for fixture offset.

Fanuc Alarm PS899 ILLEGAL PARAMETER IN G43.2 Fanuc Alarm Description Fanuc 15i An illegal parameter was specified for dynamic tool offset. Set the controlled axis number in order from the…

Fanuc Alarm PS710 ILLEGAL COMMAND IN 3–D CIR Fanuc Alarm PS710 ILLEGAL COMMAND IN SPACE–CIR (Fanuc 15) Fanuc Alarm Description Fanuc 15i In the modal state in which three–dimensional circular…

Fanuc Alarm PS711 ILLEGAL COMBINATION OF M CODES Fanuc Alarm Description Fanuc 15 M codes of the same group are specified in the same block. Or, an M code which…

Fanuc Alarm PS646 G68.2 FORMAT ERROR Fanuc Alarm Description Fanuc 15i A value of 0 is specified in the I, J, and K commands in a feature coordinate system command…

Fanuc Alarm PS647 ILLEGAL USE OF G53.1 Fanuc Alarm Description Fanuc 15i (1) The tool axis direction control command was issued before the feature coordinate system set command. Issue the…

Fanuc Alarm PS713 MANUAL INTERVENTION IN G02.4/G03.4 (ABS ON) Fanuc Alarm Description Fanuc 15i In three–dimensional circular interpolation mode (G02.4/G03.4), manual intervention was performed when the manual absolute switch was…

Fanuc Alarm PS805 ILLEGAL COMMAND Fanuc Alarm Description Fanuc 15i [I/O Device] An attempt was made to specify an illegal command during I/O processing on an I/O device. [G30 Zero…

Fanuc Alarm PS806 DEVICE TYPE MISS MATCH Fanuc Alarm Description Fanuc 15i An operation not possible on the I/O device that is currently selected in the setting was specified. This…

Fanuc Alarm PS807 PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15i An I/O interface option that has not yet been added on was specified. The external I/O device and baud…

Fanuc Alarm PS712 G02.4/G03.4 FORMAT ERROR Fanuc Alarm Description Fanuc 15i The three–dimensional circular interpolation command (G02.4/G03.4) contains an error.

Fanuc Alarm PS626 G68 FORMAT ERROR Fanuc Alarm Description Fanuc 15i There is a format error in the 3–dimensional coordinate conversion block. The alarm occurs in the following cases: (1)…

Fanuc Alarm PS630 HPCC:ILLEGAL START U/CANCEL Fanuc Alarm Description Fanuc 15 G05P10000 was specified in a mode which cannot enter the HPCC mode (See Section 2.1.1 ) The HPCC mode…

Fanuc Alarm PS645 TOO MANY G68.2 NESTING Fanuc Alarm Description Fanuc 15i The feature coordinate system set command was issued twice or more. To set a new feature coordinate system,…

Fanuc Alarm PS591 TV ERROR Fanuc Alarm Description Fanuc 15i An error was detected during the single–block TV error. The TV check can be suppressed by setting TVC parameter No….

Fanuc Alarm PS632 HPCC:ILLEGAL PARAMETER Fanuc Alarm Description Fanuc 15 The setting of a parameter is invalid.

Fanuc Alarm PS592 END OF RECORD Fanuc Alarm Description Fanuc 15i The EOR (End of Record) code is specified in the middle of a block. This alarm is also generated…

Fanuc Alarm PS633 HPCC:CRC OFS REMAIN AT CANCEL Fanuc Alarm Description Fanuc 15 The HPCC mode was canceled with a cutter compensation value retained.

Fanuc Alarm PS593 EGB PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15i Erroneous EGB parameter setting (1) The setting of SYN parameter No. 1955#0 is incorrect. (2) The slave axes…

Fanuc Alarm PS634 HPCC:ILLEGAL COMMAND CODE Fanuc Alarm Description Fanuc 15 An invalid code was specified in the HPCC mode. (Refer to 2.1.2). In a block that includes positioning, or…

Fanuc Alarm PS594 EGB FORMAT ERROR Fanuc Alarm Description Fanuc 15i Format error in the block in which EGB was specified (1) Nothing is specified to the master axis or…

Fanuc Alarm PS619 ILLEGAL AXIS(WHEEL WEAR COMPENSATION) Fanuc Alarm Description Fanuc 15i A compensation axis has been changed in grinding wheel wear compensation mode or compensation vector maintenance mode. Alternatively,…

Fanuc Alarm PS625 TOO MANY G68 NESTING Fanuc Alarm Description Fanuc 15i 3–dimensional coordinate conversion was specified more than twice. Cancel 3–dimensional coordinate conversion before executing new coordinate conversion. Fanuc…

Fanuc Alarm PS631 HPCC:NOT READY STATE Fanuc Alarm Description Fanuc 15 The RISC processor board is not ready for operation.

Fanuc Alarm PS595 ILL–COMMAND IN EGB MODE Fanuc Alarm Description Fanuc 15i An illegal instruction was issued during synchronization by EGB. (1) Slave axis was specified by G27, G28, G29,…

Fanuc Alarm PS596 EGB OVERFLOW Fanuc Alarm Description Fanuc 15i An overflow occurred during calculation of the synchronization coefficient.

Fanuc Alarm PS597 EGB AUTO PHASE FORMAT ERROR Fanuc Alarm Description Fanuc 15i Format error in block in which G80 or G81 was specified by EGB automatic phase alignment (1)…

Fanuc Alarm PS598 EGB AUTO PHASE PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15i Erroneous parameter settings relating to EGB automatic phase alignment (1) The acceleration/deceleration parameter is invalid. (2)…

Fanuc Alarm PS610 ILLEGAL G07.1 AXIS Fanuc Alarm Description Fanuc 10/11/12/15/15i An axis which cannot perform cylindrical interpolation was specified. More than one axis was specified in a G07.1 block….

Fanuc Alarm PS611 ILLEGAL G–CODE USE (G07.1 MODE) Fanuc Alarm Description Fanuc 10/11/12/15/15i A G code was specified that cannot be specified in the cylindrical interpolation mode. This alarm also…

Fanuc Alarm PS618 ILLEGAL P–DATA (WHEEL WEAR COMPENSATION) Fanuc Alarm Description Fanuc 15i The P data for selecting the compensation center in grinding wheel wear compensation is illegal.

Fanuc Alarm PS587 ILL–COMMAND IN G81 MODE Fanuc Alarm Description Fanuc 15 One of the illegal commands shown below was specified during G81 synchronization. (1) One of commands specified for…

Fanuc Alarm PS590 TH ERROR Fanuc Alarm Description Fanuc 15i A TH error was detected during reading from an input device. The read code that caused the TH error and…

Fanuc Alarm PS577 G80 FORMAT ERROR Fanuc Alarm Description Fanuc 15 Format error in that block in which the G80 code was specified (1) R falls outside the valid range.

Fanuc Alarm PS578 G80 PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15 Erroneous G80 parameter setting (1) The acceleration/deceleration parameter is invalid.