Fanuc Alarms

Fanuc Alarm PS580 ENCODE ALARM (PSWD&KEY) Fanuc Alarm Description Fanuc 15i When an attempt was made to read a program, the specified password did not match the password on the…

Fanuc Alarm PS581 ENCODE ALARM (PARAMETER) Fanuc Alarm Description Fanuc 15i When an attempt was made to punch an encrypted tape, the punch code parameter was set to EIA. Set…

Fanuc Alarm PS585 G81 PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15 Erroneous G81–parameter setting 1 (1) SYNAXS, bit 0 of parameter 1955, was erroneously set. (2) The slave axis…

Fanuc Alarm PS586 G81 FORMAT ERROR Fanuc Alarm Description Fanuc 15 Format error in the block in which the G81 code was specified (1) T (number of teeth) was not…

Fanuc Alarm PS573 EGB PARAMETER SETTING ERROR Fanuc Alarm Description Fanuc 15 EGB parameter setting error. (1) SYNAXS, bit 0 of parameter 1955, was erroneously set. (2) The rotation axis…

Fanuc Alarm PS551 DUPLICATE SPOS AXIS COMMAND Fanuc Alarm Description Fanuc 15i Two or more axes were specified on a single spindle positioning axis. (e.g. positioning by an M code…

Fanuc Alarm PS552 SPOS AXIS – OTHER AXIS SAME TIME Fanuc Alarm Description Fanuc 15i The spindle positioning axis and another axis are specified in the same block.

Fanuc Alarm PS561 ILLEGAL INDEXING ANGLE Fanuc Alarm Description Fanuc 15i The specified angle of rotation is not an integer multiple of the minimum indexing angle.

Fanuc Alarm PS562 INDEX TABLE AXIS COMMAND CAN NOT START Fanuc Alarm Description Fanuc 15i The specified index table indexing sequence is illegal.

Fanuc Alarm PS563 EXCESS ERROR OF INDEXING ANGLE Fanuc Alarm Description Fanuc 15i The specified index table indexing angle is illegal.

Fanuc Alarm PS564 INDEX TABLE AXIS – OTHER AXIS SAME TIME Fanuc Alarm Description Fanuc 15i The index table indexing axis and another axis have been specified in the same…

Fanuc Alarm PS566 INDEX TABLE AXIS DUPLICATE AXIS MODE Fanuc Alarm Description Fanuc 15i A move instruction has been issued to an axis that is not an index table indexing…

Fanuc Alarm PS572 CS AXIS DUPLICATE AXIS COMMAND Fanuc Alarm Description Fanuc 15i A currently moving axis has been specified as the Cs contour control axis.

Fanuc Alarm PS548 ILLGAL AXIS MODE Fanuc Alarm Description Fanuc 15i The spindle positioning axis/Cs contour control axis was specified during switching of the controlled axis mode.

Fanuc Alarm PS571 CS AXIS DUPLICATE AXIS MODE Fanuc Alarm Description Fanuc 15i The Cs contour control axis has been specified on an axis that is not in the Cs…

Fanuc Alarm PS542 FEED ZERO (E–CODE) Fanuc Alarm Description Fanuc 15i “0” has been instructed as the feedrate (E code).

Fanuc Alarm PS543 ILLEGAL GEAR SETTING Fanuc Alarm Description Fanuc 15i The gear ratio between the spindle and position coder, or the set position coder number of pulses is illegal…

Fanuc Alarm PS567 INDEX TABLE AXIS DUPLICATE AXIS COMMAND Fanuc Alarm Description Fanuc 15i Index table indexing was specified during axis movement or on an axis for which the index…

Fanuc Alarm PS575 ILL–COMMAND IN EGB MODE Fanuc Alarm Description Fanuc 15 One of the illegal commands shown below was specified during EGB synchronization. (1) One of commands specified for…

Fanuc Alarm PS555 SPOS AXIS DUPLICATE AXIS COMMAND Fanuc Alarm Description Fanuc 15i The spindle positioning instruction has been issued to a spindle that is currently moving or which the…

Fanuc Alarm PS541 S–CODE ZERO Fanuc Alarm Description Fanuc 15i “0” has been instructed as the S code.

Fanuc Alarm PS574 EGB FORMAT ERRO Fanuc Alarm Description Fanuc 15 Format error in the block in which the EGB command was specified (1) No command was specified for the…

Fanuc Alarm PS532 ILLEGAL USE OF DECIMAL POINT (E–CODE) Fanuc Alarm Description Fanuc 15i When the feedrate instruction contains valid data below the decimal point, the alarm is set and…

Fanuc Alarm PS553 SPOS AXIS ILLEGAL SEQUENCE NUMBER Fanuc Alarm Description Fanuc 15i Operation sequence pattern setting parameter No. 5895 for spindle positioning is out of range.

Fanuc Alarm PS533 ADDRESS F UNDERFLOW (G95) Fanuc Alarm Description Fanuc 15i The feedrate for the hole drilling axis calculated from the F and S codes is too slow in…

Fanuc Alarm PS533 S CODE ZERO Fanuc Alarm Description Fanuc 15 The S code for rigid tapping is not specified.

Fanuc Alarm PS534 ADDRESS F OVERFLOW (G95) Fanuc Alarm Description Fanuc 15i The feedrate for the hole drilling axis calculated from the F and S codes is too fast in…

Fanuc Alarm PS535 ADDRESS E UNDERFLOW (G95) Fanuc Alarm Description Fanuc 15i The feedrate for the hole drilling axis calculated from the E and S codes is too slow in…

Fanuc Alarm PS540 ADDRESS E OVERFLOW (OVERRIDE) Fanuc Alarm Description Fanuc 15i The speed obtained by applying override to the E instruction is too fast.

Fanuc Alarm PS511 DUPLICATE M–CODE (SPOS AXIS RELEASE) Fanuc Alarm Description Fanuc 15i A function to which the same code as this M code is set exists. (spindle positioning, mode…

Fanuc Alarm PS531 ILLEGAL USE OF DECIMAL POINT (F–CODE) Fanuc Alarm Description Fanuc 15i When the feedrate instruction contains valid data below the decimal point, the alarm is set and…

Fanuc Alarm PS538 ADDRESS F OVERFLOW (OVERRIDE) Fanuc Alarm Description Fanuc 15i The speed obtained by applying override to the F instruction is too fast.

Fanuc Alarm PS539 ADDRESS E UNDERFLOW (OVERRIDE) Fanuc Alarm Description Fanuc 15i The speed obtained by applying override to the E instruction is too slow.

Fanuc Alarm PS508 DUPLICATE M–CODE (INDEX TABLE REVERSING) Fanuc Alarm Description Fanuc 15i A function to which the same code as this M code is set exists. (indexing of index…

Fanuc Alarm PS510 DUPLICATE M–CODE (SPOS AXIS POSITIONING) Fanuc Alarm Description Fanuc 15i A function to which the same code as this M code is set exists. (spindle positioning, positioning)