Fanuc Alarms

Fanuc Alarm PS415 G37 MEASURING POSITION REACHED SIGNAL IS NOT PROPERLY INPUT Fanuc Alarm PS415 G37 ARRIVAL SGNL NOT ASSERTED (Fanuc 15) Fanuc Alarm Description Fanuc 15i The measurement position…

Fanuc Alarm PS418 SPINDLE & OTHER AXIS MOVE Fanuc Alarm Description Fanuc 10/11/12/15 Spindle and other axis are specified in the same block for spindle positioning.

Fanuc Alarm PS360 PARAMETER OUT OF RANGE (TLAC) Fanuc Alarm Description Fanuc 15i Illegal parameter setting. (Set value is out of range.)

Fanuc Alarm PS361 PARAMTER SETTING ERROR 1 (TLAC) Fanuc Alarm Description Fanuc 15i Illegal parameter setting. (axis of rotation setting)

Fanuc Alarm PS429 MISSING VALUE AT CNR, CHF Fanuc Alarm Description Fanuc 15i The specified movement distance is less than the specified chamfering or cornering amount in a block in…

Fanuc Alarm PS430 CODE ISN’T G01 AFTER CNR, CHF Fanuc Alarm Description Fanuc 10/11/12/15 The command following a block in which cornering or chamfering was specified is not G01. Example)…

Fanuc Alarm PS300 ILLEGAL ADDRESS Fanuc Alarm Description Fanuc 15i The axis No. address was specified even though the parameter is not an axis–type while loading parameters or pitch error…

Fanuc Alarm PS301 MISSING ADDRESS Fanuc Alarm Description Fanuc 15i The axis No. was not specified even though the parameter is an axis–type while loading parameters or pitch error compensation…

Fanuc Alarm PS330 ILLEGAL SPINDLE NUMBER Fanuc Alarm Description Fanuc 15i An spindle No. address exceeding the maximum number of controlled spindles was found while loading parameters from a tape…

Fanuc Alarm PS332 DATA WRITE LOCK ERROR Fanuc Alarm Description Fanuc 15i Could not load data while loading parameters, pitch error compensation data and work coordinate data from tape.

Fanuc Alarm PS333 DATA WRITE ERROR Fanuc Alarm Description Fanuc 15i Could not write data while loading data from tape.

Fanuc Alarm PS298 ILLEGAL INCH/METRIC CONVERSION Fanuc Alarm Description Fanuc 15i An error occurred during inch/metric switching.

Fanuc Alarm PS299 ILLEGAL ZERO RETURN COMMAND Fanuc Alarm PS299 CRC: NO INTERSECTION (Fanuc 15) Fanuc Alarm PS299 CRC: NO SOLUTION (Fanuc 10/11/12) Fanuc Alarm Description Fanuc 15i A value…

Fanuc Alarm PS278 CRC: DANGEROUS AVOIDANCE Fanuc Alarm Description Fanuc 15i Danger was judged when avoidance operation was executed by the interference check avoidance function during cutter compensation.

Fanuc Alarm PS308 MISSING DATA Fanuc Alarm Description Fanuc 10/11/12/15/15i An address not followed by a numeric value was found while loading parameters or pitch error compensation data from a…

Fanuc Alarm PS279 CRC: INTERFERENCE TO AVD. Fanuc Alarm Description Fanuc 15i Interference occurred again even though the interference avoidance vector has been calculated by the interference check avoidance function…

Fanuc Alarm PS280 ILLEGAL COMMAND IN SPIRAL Fanuc Alarm Description Fanuc 15i R was specified in the program block; 4 or more axes were specified in the program block; or…

Fanuc Alarm PS281 OVER TOLERANCE OF END POINT IN SPIRAL Fanuc Alarm Description Fanuc 15i The distance between the positions of the specified end point and the end point calculated…

Fanuc Alarm PS283 ILLEGAL IJK IN 3–D OFFSET Fanuc Alarm Description Fanuc 15i When bit 0 (ONI) of parameter No. 6029 is set to 1, I, J, and K commands…

Fanuc Alarm PS370 PARAMETER SETTING ERROR (DM3H–1) Fanuc Alarm Description Fanuc 15i Out–of–range data was set during setting of the 3–dimensional handle feed parameter.

Fanuc Alarm PS371 PARAMETER SETTING ERROR (DM3H–2) Fanuc Alarm Description Fanuc 15i An illegal axis of rotation was set during setting of the 3–dimensional handle feed parameter.

Fanuc Alarm PS304 TOO MANY DIGIT Fanuc Alarm Description Fanuc 10/11/12/15/15i Data with too many digits was found while loading parameters or pitch error compensation data from a tape.

Fanuc Alarm PS305 DATA OUT OF RANGE Fanuc Alarm Description Fanuc 15i Out–of–range data was found while loading parameters or pitch error compensation data from a tape. The values of…

Fanuc Alarm PS306 MISSING AXIS NUMBER Fanuc Alarm Description Fanuc 10/11/12/15/15i A parameter which requires an axis to be specified was found without an axis No. (address A) while loading…

Fanuc Alarm PS362 PARAMETER SETTING ERROR 2 (TLAC) Fanuc Alarm Description Fanuc 15i Illegal parameter setting (tool axis setting)

Fanuc Alarm PS302 ILLEGAL DATA NUMBER Fanuc Alarm Description Fanuc 15i A non–existent data No. was found while loading parameters or pitch error compensation data from a tape or by…

Fanuc Alarm PS303 ILLEGAL AXIS NUMBER Fanuc Alarm Description Fanuc 15i An axis No. address exceeding the maximum number of controlled axes was found while loading parameters from a tape…

Fanuc Alarm PS277 CRC: NO AVOIDANCE Fanuc Alarm Description Fanuc 15i Interference cannot be avoided as there no interference avoidance vector has been specified for the interference check avoidance function…

Fanuc Alarm PS373 PARAMETER SETTING ERROR (DM3H–4) Fanuc Alarm Description Fanuc 15i An illegal parallel axis or twin table was set during setting of the 3–dimensional handle feed parameter.

Fanuc Alarm PS307 ILLEGAL USE OF MINUS SIGN Fanuc Alarm Description Fanuc 10/11/12/15/15i Data with an illegal sign was found while loading parameters or pitch error compensation data from a…

Fanuc Alarm PS282 ILLEGAL COMMAND IN 3–D OFFSET Fanuc Alarm Description Fanuc 15i An illegal G code was specified in the 3–dimensional tool offset mode.

Fanuc Alarm PS372 PARAMETAR SETTING ERROR (DM3H–3) Fanuc Alarm Description Fanuc 15i An illegal master axis was set during setting of the 3–dimensional handle feed parameter.

Fanuc Alarm PS276 CRC: NO INTERSECTION Fanuc Alarm Description Fanuc 15i There is not point of intersection of the compensated tool center path during cutter compensation.

Fanuc Alarm PS215 ILLEGAL COMMAND IN G10.6 Fanuc Alarm PS215 TOOL RETRACTION INCORRECT (Fanuc 15) Fanuc Alarm PS215 ESCAPE ERROR (PTRR) (Fanuc 10/11/12) Fanuc Alarm Description Fanuc 15i The retract…

Fanuc Alarm PS217 ILLEGAL OFFSET VALUE Fanuc Alarm Description Fanuc 15/15i Illegal offset No.