Fanuc Alarms

Fanuc Alarm 5050 ILL–COMMAND IN CHOPPING MODE (M series) Fanuc Alarm Description A command for switching the major axis has been specified for circular threading. Alternatively, a command for setting…

Fanuc Alarm 5064 DIFFERRENT AXIS UNIT (IS–B, IS–C) (M series) Fanuc Alarm Description Circular interpolation has been specified on a plane consisting of axes having different increment systems.

Fanuc Alarm 5065 DIFFERENT AXIS UNIT (PMC AXIS) (M series) Fanuc Alarm Description Axes having different increment systems have been specified in the same DI/DO group for PMC axis control….

Fanuc Alarm 5069 WHL–C:ILLEGA P–DATA (M series) Fanuc Alarm Description The P data in selection of the grinding–wheel wear compensation center is illegal.

Fanuc Alarm 5073 NO DECIMAL POINT Fanuc Alarm Description A decimal point is not specified for a command for which a decimal point must be specified.

Fanuc Alarm 5082 DATA SERVER ERROR Fanuc Alarm Description This alarm is detailed on the data server message screen.

Fanuc Alarm 5085 SMOOTH IPL ERROR 1 Fanuc Alarm Description A block for specifying smooth interpolation contains a syntax error. or The command format of a smooth interpolation command block…

Fanuc Alarm 5300 SET ALL OFFSET DATAS AGAIN Fanuc Alarm Description After the inch/metric automatic conversion function (OIM: Bit 0 of parameter No. 5006) for tool offset data is enabled…

Fanuc Alarm 5115 SPL : ERROR (M series) Fanuc Alarm Description There is an error in the specification of the rank. No knot is specified. The knot specification has an…

Fanuc Alarm 5218 ILLEGAL PARAMETER (INCL. COMP) Fanuc Alarm Description There is an inclination compensation parameter setting error. Cause: 1. The number of pitch error compensation points between the negative…

Fanuc Alarm 5214 SCREEN COPY : DATA TRANSFER ERROR Fanuc Alarm Description Data transfer to the memory card failed. Check whether the memory card space is insufficient and whether the…

Fanuc Alarm 5213 SCREEN COPY : COMMUNICATION ERROR Fanuc Alarm Description The memory card cannot be used. Check the memory card. (Check whether the memory card is write–protected or defective.)

Fanuc Alarm 5212 SCREEN COPY : PARAMETER ERROR Fanuc Alarm Description There is a parameter setting error. Check that 4 is set as the I/O channel.

Fanuc Alarm 5199 FINE TORQUE SENSING PARAMETER Fanuc Alarm Description A parameter related to the fine torque sensing function is illegal. · The storage interval is invalid. · An invalid…

Fanuc Alarm 5198 FSSB : ID DATA NOT READ Fanuc Alarm Description Temporary assignment failed, so amplifier initial ID information could not be read.

Fanuc Alarm 5197 FSSB : OPEN TIME OUT Fanuc Alarm Description The CNC permitted FSSB to open, but FSSB was not opened.

Fanuc Alarm 5196 ILLEGAL OPERATION (HPCC) (M series) Fanuc Alarm Description Detach operation was performed in HPCC mode. (If detach operation is performed in HPCC mode, this alarm is issued…

Fanuc Alarm 5155 NOT RESTART PROGRAM BY G05 Fanuc Alarm Description During servo leaning control by G05, an attempt was made to perform restart operation after feed hold or interlock….

Fanuc Alarm 5139 FSSB : ERROR Fanuc Alarm Description Servo initialization did not terminate normally. The optical cable may be defective, or there may be an error in connection to…

Fanuc Alarm 5138 FSSB : AXIS SETTING NOT COMPLETE Fanuc Alarm Description In automatic setting mode, axis setting has not been made yet. Perform axis setting on the FSSB setting…

Fanuc Alarm 5137 FSSB : CONFIGURATION ERROR Fanuc Alarm Description FSSB detected a configuration error.

Fanuc Alarm 5136 FSSB : NUMBER OF AMPS IS SMALL Fanuc Alarm Description In comparison with the number of controlled axes, the number of amplifiers recognized by FSSB is not…

Fanuc Alarm 5135 FSSB : ERROR MODE Fanuc Alarm Description FSSB has entered error mode.

Fanuc Alarm 5134 FSSB : OPEN READY TIME OUT Fanuc Alarm Description Initialization did not place FSSB in the open ready state.

Fanuc Alarm 5124 CAN NOT COMMAND SPIRAL (M series) Fanuc Alarm Description A spiral interpolation or conical interpolation was specified in any of the following modes: 1) Scaling 2) Programmable…

Fanuc Alarm 5123 OVER TOLERANCE OF END POINT (M series) Fanuc Alarm Description The difference between a specified end point and the calculated end point exceeds the allowable range (parameter…

Fanuc Alarm 5122 ILLEGAL COMMAND IN SPIRAL (M series) Fanuc Alarm Description A spiral interpolation or conical interpolation command has an error. Specifically, this error is caused by one of…

Fanuc Alarm 5118 SPL : ERROR (M series) Fanuc Alarm Description After manual intervention with manual absolute mode set to on, NURBS interpolation was restarted.

Fanuc Alarm 5117 SPL : ERROR (M series) Fanuc Alarm Description The first control point of NURBS is incorrect.

Fanuc Alarm 5116 SPL : ERROR (M series) Fanuc Alarm Description There is a program error in a block under look–ahead control. Monotone increasing of knots is not observed. In…

Fanuc Alarm 5096 MISMATCH WAITING M–CODE Fanuc Alarm Description Different wait codes (M codes) were specified in HEAD1 and HEAD2. Correct the program.

Fanuc Alarm 5068 G31 FORMAT ERROR (M series) Fanuc Alarm Description The continuous high–speed skip command (G31 P90) has one of the following errors: 1. The axis along which the…

Fanuc Alarm 5067 (HPCC) (M series) Fanuc Alarm Description HPCC mode cannot be canceled during G51 (scaling) or G68 (coordinate system rotation). Correct the program.

Fanuc Alarm 5046 ILLEGAL PARAMETER (ST.COMP) Fanuc Alarm Description The parameter settings for straightness compensation contain an error. Possible causes are as follows: 1. A parameter for a movement axis…

Fanuc Alarm 5018 POLYGON SPINDLE SPEED ERROR (T series) Fanuc Alarm Description Function category: Polygon turning Alarm details: In G51.2 mode, the speed of the spindle or polygon synchronous axis…