Haas Alarm Codes

600 – CODE NOT EXPECTED IN THIS CONTEXT – Haas Lathe
600 – U OVER TRAVEL RANGE – Haas Mill
601 – MAXIMUM PQ BLOCKS EXCEEDED – Haas Lathe
601 – V OVER TRAVEL RANGE – Haas Mill
602 – NON-MONOTONOUS PQ BLOCKS IN X – Haas Lathe
602 – W OVER TRAVEL RANGE – Haas Mill
603 – NON-MONOTONOUS PQ BLOCKS IN Z – Haas Lathe
603 – U LIMIT SWITCH – Haas Mill
604 – NON-MONOTONOUS ARC IN PQ BLOCK – Haas Lathe
604 – V LIMIT SWITCH – Haas Mill
605 – INVALID TOOL NOSE ANGLE – Haas Lathe
605 – W LIMIT SWITCH – Haas Mill
606 – INVALID A CODE – Haas Lathe
607 – INVALID W CODE – Haas Lathe
608 – INVALID Q CODE
609 – TAILSTOCK RESTRICTED ZONE – Haas Lathe
609 – U SERVO ERROR TOO LARGE – Haas Mill
610 – G71/G72 DOMAIN NESTING EXCEEDED – Haas Lathe
610 – V SERVO ERROR TOO LARGE – Haas Mill
611 – G71/G72 TYPE I ALARM – Haas Lathe
611 – W SERVO ERROR TOO LARGE – Haas Mill
612 – G71/G72 TYPE II ALARM – Haas Lathe
612 – U SERVO OVERLOAD – Haas Mill
613 – COMMAND NOT ALLOWED IN CUTTER COMPENSATION
614 – V SERVO OVERLOAD – Haas Mill
615 – NO INTERSECTION TO OFFSETS IN CC – Haas Lathe
615 – W SERVO OVERLOAD – Haas Mill
616 – CANNED CYCLE USING P & Q IS ACTIVE – Haas Lathe
616 – U-AXIS MOTOR OVERHEAT – Haas Mill
617 – MISSING ADDRESS CODE – Haas Lathe
617 – V-AXIS MOTOR OVERHEAT – Haas Mill
618 – INVALID ADDRESS VALUE – Haas Lathe
618 – W-AXIS MOTOR OVERHEAT – Haas Mill
619 – STROKE EXCEEDS START POSITION – Haas Lathe
620 – C AXIS DISABLED
621 – C OVER TRAVEL RANGE
622 – C AXIS ENGAGEMENT FAILURE – Haas Lathe
622 – TOOL ARM FAULT – Haas Mill
623 – INVALID CODE IN G112 – Haas Lathe
624 – COMMAND NOT ALLOWED IN G14 MODE – Haas Lathe
625 – CAROUSEL POSITIONING ERROR – Haas Mill
626 – TOOL POCKET SLIDE ERROR – Haas Mill
627 – ATC ARM MOTION – Haas Mill
628 – ATC ARM POSITIONING ERROR – Haas Mill
629 – EXCEEDED MAX FEED PER REV – Haas Lathe
629 – APC-PIN CLEAR/HOME SWITCH FAULT – Haas Mill
630 – APC-DOOR SW FAULT-SWITCH NOT EQUAL TO SOLENOID – Haas Mill
631 – PALLET NOT CLAMPED – Haas Mill
632 – APC-UNCLAMP ERROR – Haas Mill
633 – APC-CLAMP ERROR – Haas Mill
634 – APC-MISLOCATED PALLET – Haas Mill
635 – APC-PAL NUM CONFLICT REC & CH – Haas Mill
636 – APC UNLOAD-SWITCH MISSED PAL 1 – Haas Mill
637 – APC UNLOAD-SWITCH MISSED PAL 2 – Haas Mill
638 – APC-DOOR NOT OPEN – Haas Mill
639 – APC-DOOR NOT CLOSED – Haas Mill
640 – APC-MISSING PALLET @ REC – Haas Mill
641 – APC-UNKNOWN CHAIN LOCATION – Haas Mill
642 – 642 APC-PIN CLEAR SWITCH FAULT – Haas Mill
643 – LOW BRAKE OIL A-AXIS – Haas Mill
644 – APC-LOW AIR PRESSURE – Haas Mill
645 – AMPLIFIER GROUND – Haas Mill
646 – VAC INPUT PHASE – Haas Mill
647 – REGEN LOAD SHORTED – Haas Mill
648 – DC BUS SHORTED – Haas Mill
649 – DC BUS UNDER VOLTAGE – Haas Mill
650 – DC BUS OVER VOLTAGE – Haas Mill
651 – Z AXIS IS NOT ZEROED – Haas Mill
652 – U ZERO RET MARGIN TOO SMALL
653 – V ZERO RET MARGIN TOO SMALL
654 – W ZERO RET MARGIN TOO SMALL
655 – MISMATCH AXIS WITH I, K CHAMFERING – Haas Lathe
655 – U CABLE FAULT – Haas Mill
656 – INVALID I, K, OR R IN G01 – Haas Lathe
656 – V CABLE FAULT – Haas Mill
657 – NOT ONE AXIS MOVE WITH CHAMFERING – Haas Lathe
657 – W CABLE FAULT – Haas Mill
658 – INVALID MOVE AFTER CHAMFERING – Haas Lathe
658 – U PHASING ERROR – Haas Mill
659 – NOT ONE AXIS MOVE WITH CHAMFERING – Haas Lathe
659 – V PHASING ERROR – Haas Mill
660 – W PHASING ERROR – Haas Mill
661 – U TRANSITION FAULT – Haas Mill
662 – V TRANSITION FAULT – Haas Mill
663 – W TRANSITION FAULT – Haas Mill
664 – U AXIS DISABLED
665 – V AXIS DISABLED – Haas Lathe
665 – V AXIS DISABLED – Haas Mill
666 – W AXIS DISABLED
667 – U AXIS LINEAR SCALE Z FAULT – Haas Mill
668 – V AXIS LINEAR SCALE Z FAULT – Haas Mill
669 – W AXIS LINEAR SCALE Z FAULT – Haas Mill
670 – TT or B OVER TRAVEL RANGE – Haas Mill
671 – TT or B LIMIT SWITCH – Haas Mill
673 – TT or B SERVO ERROR TOO LARGE – Haas Mill
674 – TT or B SERVO OVERLOAD – Haas Mill
675 – TT or B-AXIS MOTOR OVERHEAT – Haas Mill
676 – TT or B MOTOR Z FAULT – Haas Mill
677 – TT or B AXIS Z CH MISSING – Haas Mill
678 – TT or B AXIS DRIVE FAULT – Haas Mill
679 – TT or B ZERO RET MARGIN TOO SMALL – Haas Mill
680 – TT or B CABLE FAULT – Haas Mill
681 – TT or B PHASING ERROR – Haas Mill
682 – TT or B TRANSITION FAULT – Haas Mill
683 – TT or B AXIS DISABLED – Haas Mill
684 – TT or B AXIS LINEAR SCALE Z FAULT – Haas Mill
685 – V MOTOR Z FAULT – Haas Mill
686 – W MOTOR Z FAULT – Haas Mill
687 – U MOTOR Z FAULT – Haas Mill
688 – U AXIS Z CH MISSING – Haas Mill
689 – V AXIS Z CH MISSING – Haas Mill
690 – W AXIS Z CH MISSING – Haas Mill
691 – U AXIS DRIVE FAULT – Haas Mill
692 – V AXIS DRIVE FAULT – Haas Mill
693 – W AXIS DRIVE FAULT – Haas Mill
694 – ATC SWITCH FAULT – Haas Mill
695 – ATC DOUBLE-ARM CYLINDER TIME OUT – Haas Mill
696 – ATC MOTOR TIME OUT – Haas Mill
697 – ATC MOTOR FAULT – Haas Mill
698 – ATC PARAMETER ERROR – Haas Mill

Pages: 1 2 3 4 5 6 7 8 9

Haas

Manuals

G & M Codes

Alarms

Settings

Parameters

Mill Programming

Lathe Programming

Programming

M Code Tutorials

Haas

Manuals

G & M Codes

Alarms

Settings

Parameters

Mill Programming

Lathe Programming

Programming

M Code Tutorials

Haas Alarm Codes

More ...