Haas Parameters

Haas Parameter 296 MAX OVER VOLT TIME Specifies the amount of time (in 50ths of a second) that an overvoltage condition (Alarm 119, Over Voltage) will be tolerated before the automatic…

Haas Parameter 210 X TOOL CHANGE OFFSET Used on the HS-2RP mill for X axis displacement from the home position to tool change position. If this parameter contains an incorrect value,…

Haas Parameter 297 MAX OVER HEAT TIME Specifies the amount of time (in 50ths of a second ) that an overheat condition (Alarm 122, Regen Overheat) will be tolerated before the…

Haas Parameter 197 Sp SWITCH FREQUENCY Frequency at which the spindle motor windings are switched. Note that there is a hysteresis band around this point, defined by Parameter 198.

Haas Parameter 229 X LEAD COMP 10E9 Sets the X-axis lead screw compensation signed parts per billion.

Haas Parameter 198 Sp SWITCH HYSTERESIS Defines the + hysteresis band around Parameter 197. For example, if Parameter 197 is 85 Hz, and Parameter 198 is 5 Hz, the switching will…

Haas Parameter 230 Y LEAD COMP 10E9 Sets the Y-axis lead screw compensation signed parts per billion.

Haas Parameter 199 Sp PRE-SWITCH DELAY Amount of time allowed for the motor current to drop before winding change contactors are switched.

Haas Parameter 231 Z LEAD COMP 10E9 Sets the Z-axis lead screw compensation signed parts per billion.

Haas Parameter 246 3RD AUX MIN TRAVEL Sets the maximum travel of the third auxiliary (V) axis in the negative direction.

Haas Parameter 291 HYD TS NO MOT. TIME – Haas Lathe Number in milliseconds that must pass with no B-axis encoder change before the control decides that the tailstock has stopped….

Haas Parameter 183 Sp MAX FREQ See Parameter 8 for description. Frequency at which the motor will be run when maximum spindle rpm is commanded. Units: 0.01 Hz (two implied decimal…

Haas Parameter 219 CNVYR RETRY LIMIT Number of times that the conveyor will cycle through the reverse/forward sequencing when an overcurrent is sensed, before the conveyor will shut down. An overcurrent…

Haas Parameter 273 Y SCREW COMP T. CONST Thermal compensation time constant, and is the time constant governing the rate of cool down of the screw.

Haas Parameter 185 Sp FUSE LEVEL See Parameter 10 for description.

Haas Parameter 220 CNVYR RETRY TIMEOUT Time in 1/50 seconds between consecutive overcurrents in which an overcurrent is considered to be another retry. If this time passes between overcurrents, the retry…

Haas Parameter 274 Z SCREW COMP T. CONST Thermal compensation time constant, and is the time constant governing the rate of cool down of the screw.

Haas Parameter 250 CHUCK UNCLAMP DELAY – Haas Lathe Dwell time allowed after unclamping the chuck (an M11 command). Program execution will not continue until this time has expired. Units are…

Haas Parameter 280 Y SCALE GAIN MULT See Parameter 279 for description.

Haas Parameter 250 TOOL UNCLAMP DELAY – Haas Mill Provides a delay after the tool has been unclamped and before the spindle is backed away at the beginning of a tool…

Haas Parameter 251 A DOOR OPEN ERRTIME Supports the Auto-Door feature. It is used for several things: 1) It specifies the number of 50ths of a second for the motor…

Haas Parameter 252 TAIL ST. OVERLOAD – – Haas Lathe Determines overload limit when the tailstock is traveling in the minus direction, toward the spindle. It is an arbitrary value based…

Haas Parameter 252 GEAR MOTOR TIMEOUT – Haas Mill Supports the Auto-Door feature. It specifies the length of time (in ms) that is allowed for the door to begin opening. If…

Haas Parameter 298 Y AX RTAP BACKLASH – Haas Lathe This parameter is normally set to zero, but can be adjusted by the user (to a number typically between 0…

Haas Parameter 253 TAIL ST. OVERLOAD + – Haas Lathe Determines overload limit when tailstock is traveling in positive direction, away from spindle. Value for Parameter 253 should be approximately twice…

Haas Parameter 285 X LINEAR SCREW OFFS Used on machines with linear scales. This parameter accounts for the unused portion of the ballscrew between zero and the actual motor.

Haas Parameter 298 MAX FEED (DEG/MIN) – Haas Mill Used on 5-axis mills. Maximum rotary feedrate in degrees per minute. Any attempt at cutting faster than this will result in “LIM”…

Haas Parameter 286 Y LINEAR SCREW OFFS See Parameter 285 for description.

Haas Parameter 287 Z LINEAR SCREW OFFS See Parameter 285 for description.

Haas Parameter 288 A LINEAR SCREW OFFS – Haas Mill See Parameter 285 for description. N/A for lathes.

Haas Parameter 289 B LINEAR SCREW OFFS – Haas Mill See Parameter 285 for description. N/A for lathes.

Haas Parameter 249 CHUCK CLAMP DELAY – Haas Lathe Dwell time allowed after clamping the chuck (an M10 command). Program execution will not continue until this time has expired. Units are…

Haas Parameter 293 HYD TS SLOW DISTNCE – Haas Lathe Sets the distance, prior to a target point, where the tailstock will transition from a rapid movement to a feed….

Haas Parameter 249 TOOL CLAMP DELAY – Haas Mill Provides a delay after the tool has been clamped and before retraction of the tool carousel at the end of a…

Haas Parameter 293 AUTO DOOR BUMP – Haas Mill Supports the Auto-Door feature. It specifies the length of time (in 50ths of a second) that the motor should be reactivated after…