Haas Parameters

Haas lathe/mill parameters

Haas Parameter 283 B SCALE GAIN MULT

Haas Parameter 283 B SCALE GAIN MULT See Parameter 279 for description.

Haas Parameter 284 Sp SCALE GAIN MULT – Haas Mill

Haas Parameter 284 Sp SCALE GAIN MULT – Haas Mill See Parameter 279 for description.

Haas Parameter 255 CONVEYOR TIMEOUT

Haas Parameter 255 CONVEYOR TIMEOUT The number of minutes the conveyor will operate without any motion or keyboard action. After this time, the conveyor will automatically shut off. Note that this…

Haas Parameter 301 AUTOFEED-MIN-LIMIT

Haas Parameter 301 AUTOFEED-MIN-LIMIT Works with the Autofeed feature. It specifies the minimum allowable feedrate override percentage that the Autofeed feature can use and should initially be set to 1. NOTE:…

Haas Parameter 256 PALLET LOCK INPUT

Haas Parameter 256 PALLET LOCK INPUT The setting for EC-300 must be 26, the EC-400 must be 32, and the MDC-1 must be 27, or Alarm 180 will occur when the…

Haas Parameter 302 FEED ACCEL MEDIUM – Haas Mill

Haas Parameter 302 FEED ACCEL MEDIUM – Haas Mill Supports the motion control feature. This is the acceleration that applies to feed motion in encoder steps per second squared selected by…

Haas Parameter 272 X SCREW COMP T. CONST

Haas Parameter 272 X SCREW COMP T. CONST Thermal compensation time constant, and is the time constant governing the rate of cool down of the screw.

Haas Parameter 303 FEED T CONST MEDIUM – Haas Mill

Haas Parameter 303 FEED T CONST MEDIUM – Haas Mill Supports the motion control feature. It is the base 2 exponent of the feed time constant in milliseconds when Medium smoothness…

Haas Parameter 248 SMTC RLY ON/OFF DLY – Haas Mill

Haas Parameter 248 SMTC RLY ON/OFF DLY – Haas Mill Vertical mills with sidemount tool changers only. It specifies the time needed (in milliseconds) between turning off one relay and turning…

Haas Parameter 292 AUTO DOOR PAUSE – Haas Mill

Haas Parameter 292 AUTO DOOR PAUSE – Haas Mill Supports the Auto-Door feature. It specifies the length of a pause (in 50ths of a second) that occurs during the door close…

Haas Parameter 329 Z SCALES PER INCH

Haas Parameter 329 Z SCALES PER INCH Used on machines equipped with linear scales.

Haas Parameter 305 SERVO PO BRK DLY – Haas Mill

Haas Parameter 305 SERVO PO BRK DLY – Haas Mill The SRV PO (Servo Power On) discrete output is used to engage and disengage an axis brake. This parameter is used…

Haas Parameter 330 A SCALES PER INCH

Haas Parameter 330 A SCALES PER INCH Used on machines equipped with linear scales.

Haas Parameter 306 POCKET UP/DN DELAY – Haas Mill

Haas Parameter 306 POCKET UP/DN DELAY – Haas Mill Supports the side-mount tool changers. It specifies the time allowed (in milliseconds) for the tool pocket to be raised or lowered. If…

Haas Parameter 331 B SCALES PER INCH

Haas Parameter 331 B SCALES PER INCH Used on machines equipped with linear scales.

Haas Parameter 307 POCKT UN/LOCK DELAY – Haas Mill

Haas Parameter 307 POCKT UN/LOCK DELAY – Haas Mill Supports side-mount tool changers. It specifies the time allowed (in milliseconds) to lock or unlock a tool pocket. For mills without a…

Haas Parameter 333 X SCALES PER REV

Haas Parameter 333 X SCALES PER REV Used on machines equipped with linear scales.

Haas Parameter 281 Z SCALE GAIN MULT

Haas Parameter 281 Z SCALE GAIN MULT See Parameter 279 for description.

Haas Parameter 282 A SCALE GAIN MULT

Haas Parameter 282 A SCALE GAIN MULT See Parameter 279 for description.

Haas Parameter 321 RP DRAWBAR UP TIME – Haas Mill

Haas Parameter 321 RP DRAWBAR UP TIME – Haas Mill Time required for the drawbar to move up. Units are milliseconds.

Haas Parameter 322 GEARMOTOR BUMP TIME – Haas Lathe

Haas Parameter 322 GEARMOTOR BUMP TIME – Haas Lathe Supports Haas Servo Bar 300 bar feeder. Gear motor run time for bump and internal functions. Units are in milliseconds.

Haas Parameter 322 TOOL CLEAN 1 ON – Haas Mill

Haas Parameter 322 TOOL CLEAN 1 ON – Haas Mill Tool arm angle to start air blast Units are degrees x 1000.

Haas Parameter 253 SPIGOT FWD POS DLY – Haas Mill

Haas Parameter 253 SPIGOT FWD POS DLY – Haas Mill Specifies the length of a delay (units are ms) when moving the coolant spigot forward. This parameter should be set to…

Haas Parameter 299 AUTOFEED-STEP-UP

Haas Parameter 299 AUTOFEED-STEP-UP Works with Autofeed. It specifies the feedrate step-up percentage per second and should initially be set to 10.

Haas Parameter 254 SPINDLE CENTER – Haas Lathe

Haas Parameter 254 SPINDLE CENTER – Haas Lathe Reserved for service use only.

Haas Parameter 300 AUTOFEED-STEP-DOWN

Haas Parameter 300 AUTOFEED-STEP-DOWN Works with the Autofeed feature. It specifies the feedrate step-down percentage per second and should initially be set to 20.

Haas Parameter 316 MEASURE BAR RATE – Haas Lathe

Haas Parameter 316 MEASURE BAR RATE – Haas Lathe Supports the Haas Servo Bar 300 bar feeder. It is the rate at which the bars are measured. Units are inches*1000.

Haas Parameter 316 APC PAL. CLAMP TIME – Haas Mill

Haas Parameter 316 APC PAL. CLAMP TIME – Haas Mill Time required to clamp the APC pallet to the receiver. Units are milliseconds.

Haas Parameter 317 MEASURE BAR INC – Haas Lathe

Haas Parameter 317 MEASURE BAR INC – Haas Lathe Supports Haas Servo Bar 300 bar feeder. This is increment used for bar measurement. Units are inches*10,000

Haas Parameter 247 4TH AUX MIN TRAVEL

Haas Parameter 247 4TH AUX MIN TRAVEL Sets the maximum travel of the fourth auxiliary (W) axis in the negative direction.

Haas Parameter 291 LOW BRAKE OIL TIME – Haas Mill

Haas Parameter 291 LOW BRAKE OIL TIME – Haas Mill Supports EC-1600 A-axis brake oil sensor. Units are seconds. When set to non-zero number and sensor indicates low oil condition for…

Haas Parameter 248 CHUCK UNCLAMP RPM – Haas Lathe

Haas Parameter 248 CHUCK UNCLAMP RPM – Haas Lathe rpm above which the chuck will not operate. If the spindle is spinning faster than this value the chuck will not…

Haas Parameter 292 HYD TS RTRACT MARGN) – Haas Lathe

Haas Parameter 292 HYD TS RTRACT MARGN) – Haas Lathe Sets the acceptable range, in encoder steps, for the retract point. When the tailstock stops anywhere within this range, the control…

Haas Parameter 305 SERVO PO BRK DLY – Haas Lathe

Haas Parameter 305 SERVO PO BRK DLY – Haas Lathe Time (in milliseconds) that the control should wait after turning off the Hyd Pump Enable relay (which will activate the brake)…

Haas Parameter 318 APC PAL. CHAIN TIME – Haas Mill

Haas Parameter 318 APC PAL. CHAIN TIME – Haas Mill Time required to cycle the chain. It should be set to 8000. Units are milliseconds.