Okuma Alarms Errors

Okuma Alarm-B 2366 TOOL RADIUS COMP. No spec. The cutter radius compensation ON command* is designated for the control not equipped with the cutter radius compensation function. * Compensation ON…

Okuma Alarm-B 2367 TOOL RADIUS COMP. NOSE-R comp. surface change The designated plane for the cutter radius compensation or nose R compensation is changed during the compensation mode is active.Before…

Okuma Alarm-B 2353 CHAMFERING G01 mode Chamfering commands are designated in other than G01 mode. Object SYSTEM Code None->No G code programmed 2->G02 3->G03 1F->G31 20->G32 21->G33 22->G34 23->G35 FE->G00…

Okuma Alarm-B 2354 CHAMFERING L over In chamfering commands, designated L value is larger than the axis movement distance. Object SYSTEM Code Hexadecimal number of axis movement distance Probable Faulty…

Okuma Alarm-B 2355 CHAMFERING L illegal order In chamfering commands, no L command is designated, or designated L value is not:-99999.999

Okuma Alarm-B 2356 CHAMFERING X, Z illegal order In chamfering commands, either both X and Z commands are designated, or neither X nor Z command is designated. Designated X or…

Okuma Alarm-B 2357 CHAMFERING Any angle calculation Calculation error during the calculation of automatic chamfering with an arbitrary angle. Object SYSTEM Code XYY YY: bit0->Overflow in converting into integer bit1->Exponential…

Okuma Alarm-B 2364 NOSE-R COMP. Entrance command error Tool nose radius compensation mode entry is intended in other than permissible manner, and compensated point cannot be calculated. Object SYSTEM Code…

Okuma Alarm-B 2365 NOSE-R COMP. Thread cutting cycle G31, G32 or G33 calling for thread cutting cycle is designated during the tool nose radius compensation mode. Object SYSTEM Code 1F->G31…

Okuma Alarm-B 2363 NOSE-R COMP. No cross point Point of intersection cannot be calculated in line to arc or arc to arc intersection. Object SYSTEM Code 1->Straight line to arc…

Okuma Alarm-B 2368 TOOL RADIUS COMP. C-axis separation The cutter radius compensation ON command is designated while the C-axis joint command (M110) is not designated. Probable Faulty Locations Program error…

Okuma Alarm-B 2369 TOOL RADIUS COMP. QA command QA command (the number of C-axis revolutions for positioning) was issued during tool radius compensation. Probable Faulty Locations Program error Program Example:…

Okuma Alarm-B 2370 TOW-ALONG TAILSTOCK MOVEMENT no spec. G152 is designated although the control has no tow-along tailstock specification. Probable Faulty Locations Program error Program Example:N010 G152 W100 Measures to…

Okuma Alarm-B 2371 TOW-ALONG TAILSTOCK MOVEMENT condition G152 (tow-along tailstock positioning cycle) is designated in other than G13 (A saddle) mode. G152 is designated without a W command. G152 is…

Okuma Alarm-B 2372 LASER MEASUREMENT no spec. An attempt is made to execute the LMW and LMV commands although the Inductosyn pitch error compensation specification is not supported (excluding LR15)….

Okuma Alarm-B 2374 LAP No spec. G85, G86, G87 or G88 calling for LAP mode is designated although the control has no LAP specification. Object SYSTEM Probable Faulty Locations Program…

Okuma Alarm-B 2375 LAP B illegal order B command specifying the tool tip angle in G88 LAP mode is either B < 0-deg or B >= 180-deg. G88: Calls continuous…

Okuma Alarm-B 2376 LAP D illegal order In G85, G86 and G88 LAP mode, either no D command is designated, or the designated D value is either negative or there…

Okuma Alarm-B 2377 LAP DA(DB) illegal order When G84 and XA (ZA) or XB (ZB) are designated in G85 LAP mode, the DA or DB command value is negative or…

Okuma Alarm-B 2378 LAP H illegal order In G88 LAP mode, no H command is designated, or designated H value is negative or there are too many digits. G88: Calls…

Okuma Alarm-B 2380 LAP U(W) illegal order LAP command G85, G86, G87, or G88 has a U value (finish allowance of X-axis component) or a W value (finish allowance of…

Okuma Alarm-B 2381 LAP U(W) > H In G88 LAP mode, designated finish allowance U or W is larger than the thread height H. G88: Calls continuous thread cutting cycle….

Okuma Alarm-B 2382 LAP XA(ZA), XB(ZB) illegal order In G85 LAP mode, the number of digits of the designated XA (ZA) or XB (ZB) command is larger than the allowable…

Okuma Alarm-B 2373 LASER MEASUREMENT condition Conditions in which the laser measurement commands LMW and LMV have been executed are not correct. Object SYSTEM Code 1->The command is designated for…

Okuma Alarm-B 2379 LAP H-U(W) < D (M73) In M73 of G88 LAP mode, the value "thread height H - finish allowance U (W)" is smaller than D, and finish...

Okuma Alarm-B 2387 Unable to LAP Control LAP control is impossible. (Overflow of control counter for LAP control) Object SYSTEM Probable Faulty Locations The LAP control software has been destroyed….

Okuma Alarm-B 2388 LAP No G-code No G80 command up to the end of the program after G81 or G82 is designated. G81 or G82 is not designated in the…

Okuma Alarm-B 2386 LAP Sequence name In the block containing G85 or G86 calling for LAP mode, no sequence name is designated, or the designated sequence name is not found…

Okuma Alarm-B 2383 LAP Calculation error Calculation alarm during LAP processing. (When calculating arc center and radius in G85) G85: Calls rough bar turning cycle. Object SYSTEM Code XX: bit0->Overflow…

Okuma Alarm-B 2384 LAP Down step number over In G85 LAP mode, the number of descending steps exceeds ten. G85: Calls rough bar turning cycle. Object SYSTEM Probable Faulty Locations…

Okuma Alarm-B 2385 LAP Entry in LAP During LAP control, LAP command (G85, G86, G87 and G88) is designated. G85: Calls rough bar turning cycle. G86: Calls rough copy turning…

Okuma Alarm-B 2390 LAP Entry in NOSE-R comp. While nose radius compensation mode is active, G code calling for LAP mode (G85, G86, G87 and G88) is designated. G85: Calls…

Okuma Alarm-B 2391 LAP Shape designation A defective shape is defined for LAP. Object SYSTEM Code 1->Overflow of coordinate values 3->The first block includes a circular interpolation command. 4->The circular…

Okuma Alarm-B 2392 MULTI CYCLE B illegal order B < 0-deg or B >= 180-deg In G71, G72 thread cutting cycle, tangent (B/2) is negative or resulted in overflow. G71:…

Okuma Alarm-B 2399 MULTI CYCLE L illegal order In G73 and G74 grooving cycle, numerical value of L command is not: 0 < L