Selca G00 Axis rapid positioning

Haas G00 Rapid Motion Positioning – Haas Mill G00 G code is used to move the machines axis at the maximum speed. G00 is primarily used to quickly position the…

Haas G00 Rapid Motion Positioning – Haas Lathe G00 G code is used to move the machines axis at the maximum speed. G00 is primarily used to quickly position the…

Selca G88 Spaced plane drilling fixed cycle ContentsProgrammingParameters Programming G88 [X… Y…] Z… J… [K…] [F…] [D8=…] Parameters Parameter Description X,Y hole coordinates. Z first wall depth. J drilling starting…

Selca G09 Deceleration at block end Programming G09 X… Y… Z… Enabled: only in the block in which it is programmed.

Selca G28 Cusp point of a SPLINE curve Programming G28 Enabled: only in the block in which it is programmed.

Selca G845 G846 Manual axis control by handwheels during machining ContentsG845 Cancels G846ProgrammingG846 Manual axis control by handwheels during machiningProgrammingParameters G845 Cancels G846 G845 Cancels G846 Programming G845 Enabled: only…

Selca G774 Roll-Over rotary axes (only for S4000 Series CNCs) ContentsProgrammingParameters Programming G774 [A] [B] [C] [D0=…] [D1=…] Parameters Parameter Description A, B,C name of the rotary axis where to…

Selca G81 Drilling /spot facing fixed cycle ContentsProgrammingParameters Programming G81 [X… Y…] Z… [I…] J… [Q…] [K…] [F…] [D8=…] [D9=1] [D10=…] [D11=…] [D13=…] Parameters Parameter Description X,Y hole coordinates. Z…

Selca G60 G61 Scaling factor ContentsG60 Cancels G61ProgrammingG61 Scaling factorProgrammingParametersG61 Programmable zone scalingProgrammingParameters G60 Cancels G61 G60 Cancels G61 (scaling factor) Programming G60 G61 Scaling factor G61 Scaling factor Programming…

Selca G83 Deep drilling fixed cycle with tool retraction for chip discharge ContentsProgrammingParameters Programming G83 [X… Y…] Z… J… I… [Q…] [K…] [F…] [D0=…] [D7=1] [D8=…] [D9=1] Parameters Parameter Description…

Selca G82 Deep mixed drilling cycle ContentsProgrammingParameters Programming G82 [X… Y…] Z… I… J… [Q…] [K…] [F…] [D0=…] [D7=1] [D8=…] [D9=1] [D10=…] [D11=…] [D12=…] [D13=…] [D14=…] Parameters Parameter Description X,Y…

Selca G86 Boring fixed cycle ContentsProgrammingParameters Programming G86 [X… Y…] Z… J… [Q…] [K…] [I…] [F…] [D0=…] [D7=…] [D8=…] [D9=1] Parameters Parameter Description X,Y hole coordinates. Z hole bottom plane….

Selca G760 G761 Axis travel delimitation ContentsG760 Cancels G761ProgrammingG761 Axis travel delimitationProgrammingParameters G760 Cancels G761 G760 Cancels G761 Programming G760 G761 Axis travel delimitation G761 Axis travel delimitation Programming G761…

Selca G17 G18 G19 Plane selection ContentsG17 Plane selection XYProgrammingG17 Selection of planes different than XYProgrammingParametersG18 Plane selection ZXProgrammingG19 Plane selection YZProgramming G17 Plane selection XY G17 Plane selection (XY…

Selca G872 ON /OFF touch probe measuring cycle in space ContentsProgrammingParameters Programming G872 [X…] [Y…] [Z…] [I…] [F…] [R] Parameters Parameter Description X,Y,Z expected coordinates of the point to be…

Selca G873 Touch /copying probe measuring cycle in space ContentsProgrammingParameters Programming G873 [X…] [Y…] [Z…] [I…] [F…] [R] Parameters Parameter Description X,Y,Z expected coordinates of the point to be measured….

Selca G9999 Synchronization of program execution with tool path display Programming G9999 Enabled: only in the block in which it is programmed.

Selca G75 G76 Polar coordinate programming ContentsG75 Cancels G76ProgrammingG76 Polar coordinate programmingProgrammingParameters G75 Cancels G76 G75 Cartesian coordinate programming (cancels G76) Programming G75 [X…] [Y…] [Z…] Enabled: (default) until a G76…

Selca G30 G31 Continuous motion mode with automatic feed adjustment ContentsG30 Cancels G31ProgrammingG31 Continuous motion modeProgrammingParameters G30 Cancels G31 G30 Cancels G31 and re-establishes deceleration at block end Programming G30…

Selca G74 Rounding off in the ±180° range for rotary axes ContentsProgrammingParameters Programming G74 [A] [B] [C] Parameters Parameter Description A, B, C name of the rotary axis where to…