Selca G888 Profile learning parameters
Contents
G888 I... J... Q... F...
| Parameter | Description |
|---|---|
| I | slowing down distance. Speed reduction begins I mm before the critical zone and ends I mm after the critical zone. |
| J | critical radius of curvature. J=2 x Probe Radius by default. |
| Q | chord length for the calculation of the radii of curvature. Q= 1/2 Probe Radius by default. |
| F | copying speed for the profile sections adjacent to the critical points. |
Selca G881 Copying cycle start ContentsProgrammingParameters Programming G881 X… Y… I… K… Q… F… Parameters Parameter Description X or Y or Z coordinates of a point (not reached by the…
Selca G736 Surfaces defined by a plane profile and one or more section profiles: plane profile and parameters ContentsProgrammingParameters Programming G736 I… [X… Y…] [J…] [K…] [Q…] [D0=…] [D1=…] [D2=…]…
ContentsSelca G884 Copying parameters for unidirectional passesProgrammingParametersSelca G884 Radial copying parametersProgrammingParameters Selca G884 Copying parameters for unidirectional passes Selca G884 Copying parameters for unidirectional passes (3, 4, 9 and 10 copying…
Selca G777 Opens profile pocket programming and set parameters ContentsProgrammingParameters Programming G777 Z… J… I… [Q…] [D1=…] [D2=…] [D3=…] [D4=…] [D5=…] [D6=…] [D7=1] Parameters Parameter Description Z pocket bottom depth….
Selca G721 Calculates and stores equidistant points on a profile ContentsProgrammingParameters Programming G721 I… J… K… [Q…] [D0=…] Parameters Parameter Description I distance between points (alternative to J). J number…
Selca G883 Digitizing cycle ContentsProgrammingParameters Programming G883 I… J… K… Q… [D0=…] [D1=…] [AXES] LNAME: Parameters Parameter Description I chordal error – maximum allowable error between the theoretic curve and…
Selca G710 G711 Profile storing ContentsG710 Cancels G711ProgrammingG711 Profile storingProgrammingParameters G710 Cancels G711 G710 Cancels G711 (profile storing) Programming G710 G711 Profile storing G711 Profile storing Programming G711 K… [X……
Selca G34 Opens programming of the profile delimiting the zone of ruled surface to be machined ContentsProgrammingParameters Programming G34 [I0] Parameters Parameter Description I0 the delimitation profile is not offset…
Selca G41 Enables tool radius compensation, tool left of profile ContentsProgrammingParameters Programming G41 [K…] [I1] [Q…] [D0=…] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Selca G42 Enables tool radius compensation, tool right of profile ContentsProgrammingParameters Programming G42 [K…] [I1] [Q…] [D0=1] [D1=1] [D2=1] Parameters Parameter Description K selects profile approach mode: K1: automatic approach…
Selca G726 Ruled surfaces between two profiles: first profile ContentsProgrammingParameters Programming G726 [X… Y…] Z… I… [J…] [D1=…] [D2=…] Parameters Parameter Description X,Y starting point of the first profile. Z…
Selca G889 Copying probe data ContentsProgrammingParameters Programming G889 I… J… K… Q… [X…] [Y…] [Z…] [D0=] [D1=1] Parameters Parameter Description I nominal deflexion on the plane. J probe tracer point…
Selca G879 Closing of limit definition ContentsProgrammingParameters Programming G879 [I…] [J…] [Q…] Parameters Parameter Description I probe axis upper limit in copying mode 5. J probe axis lower limit in…
Selca G880 Profile end in copying mode 11 Programming G880 The profile to be copied shall be programmed between a G881 and a G880 code.
Selca G737 Surfaces defined by a plane profile and one or more section profiles: section profiles ContentsProgrammingParameters Programming G737 [Q…] [K1] Parameters Parameter Description Q number of the section profile…
Selca G727 Ruled surfaces between two profiles: second profile ContentsProgrammingParameters Programming G727 [X… Y…] Z… Parameters Parameter Description X,Y starting point of the second profile. Z Z-coordinate of the second…
Selca G735 Spiral milling ContentsProgrammingParameters Programming G735 I… [J…] [K…] [Q…] [Z…] Parameters Parameter Description I increment all along the profile (Q1: default) increment on 1mmof profile (Q2) number of…
Selca G40 Exit from profile and cutter compensation disable ContentsProgrammingParameters Programming G40 [K…] [X… Y…] Parameters Parameter Description K selects profile exit mode: K1: automatic profile exit with a straight…
Selca CNC 4000/3000 Series control G-Functions/ G-codes for cnc machinists who work on cnc machines with Selca cnc controls. These Selca G Functions work on following Selca cnc controls, Selca…
Selca G730 G731 High speed milling of profiles defined by points ContentsG730 Cancels G731ProgrammingG731 High speed milling of profiles defined by pointsProgrammingParameters G730 Cancels G731 G730 Cancels G731 (Only for…
