Sinumerik Alarms

Sinumerik Alarm 300614 Axis %1 drive %2 time monitoring of motor temperature Parameters: %1 = NC axis number %2 = Drive number Definitions: The motor temperature (measured via the temperature…

Sinumerik Alarm 300701 Axis %1 drive %2 start-up required Parameters: %1 = NC axis number %2 = Drive number Definitions: This alarm appears when installing and starting up for the…

Sinumerik Alarm 300720 Axis %1 drive %2 maximum motor speed invalid Parameters: %1 = NC axis number %2 = Drive number Definitions: Because of the high maximum motor speed in…

Sinumerik Alarm 300708 Axis %1 drive %2 current controller cycle times of axes differ Parameters: %1 = NC axis number %2 = Drive number Definitions: The current controller cycle MD…

Sinumerik Alarm 300709 Axis %1 drive %2 speed controller cycle times of axes differ Parameters: %1 = NC axis number %2 = Drive number Definitions: The speed controller cycle MD…

Sinumerik Alarm 300725 Axis %1 drive %2 number of encoder marks of measuring system invalid Parameters: %1 = NC axis number %2 = Drive number Definitions: The number of encoder…

Sinumerik Alarm 300710 Axis %1 drive %2 position controller cycle times of axes differ Parameters: %1 = NC axis number %2 = Drive number Definitions: In a 2-axis module, the…

Sinumerik Alarm 300726 Axis %1 drive %2 voltage constant is zero Parameters: %1 = NC axis number %2 = Drive number Definitions: The value in drive MD 1114: $MD_EMF_VOLTAGE is…

Sinumerik Alarm 300711 Axis %1 drive %2 monitoring cycle times of axes differ Parameters: %1 = NC axis number %2 = Drive number Definitions: The monitoring cycle MD 1002: $MD_MONITOR_CYCLE_TIME…

Sinumerik Alarm 300712 Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible Parameters: %1 = NC axis number %2 = Drive number Definitions: On a 2-axis…

Sinumerik Alarm 300728 Axis %1 drive %2 adaption factor torque/current too high Parameters: %1 = NC axis number %2 = Drive number Definitions: The matching factor from setpoint torque to…

Sinumerik Alarm 300713 Axis %1 drive %2 lead time for position controller invalid Parameters: %1 = NC axis number %2 = Drive number Definitions: The derivative-action time describes the point…

Sinumerik Alarm 300729 Axis %1 drive %2 motor zero-speed current less than or equal to zero Parameters: %1 = NC axis number %2 = Drive number Definitions: The value in…

Sinumerik Alarm 300714 Axis %1 drive %2 power section code invalid Parameters: %1 = NC axis number %2 = Drive number Definitions: The code number of the power section entered…

Sinumerik Alarm 300715 Axis %1 drive %2 maximum power section current less than or equal to zero Parameters: %1 = NC axis number %2 = Drive number Definitions: The maximum…

Sinumerik Alarm 300716 Axis %1 drive %2 torque constant less than or equal to zero Parameters: %1 = NC axis number %2 = Drive number Definitions: 1. The value in…

Sinumerik Alarm 300717 Axis %1 drive %2 motor moment of inertia less than or equal to zero Parameters: %1 = NC axis number %2 = Drive number Definitions: The value…

Sinumerik Alarm 300718 Axis %1 drive %2 calculation dead time of current controller less than or equal to zero Parameters: %1 = NC axis number %2 = Drive number Definitions:…

Sinumerik Alarm 300719 Axis %1 drive %2 motor not parameterized for delta operation Parameters: %1 = NC axis number %2 = Drive number Definitions: On activating the star/delta switchover by…

Sinumerik Alarm 105005 Only workpieces can be inserted here Definitions: The file type of the previously copied file is not _wpd and cannot be inserted into the work- piece directory….

Sinumerik Alarm 104025 No magazine configured Definitions: No magazine was configured. Reactions: – – Remedy: Configure a magazine via the machine data. Program Continuation: Internal

Sinumerik Alarm 104024 Error during tool unloading Definitions: An error occurred while a tool was being unloaded; the procedure has been aborted. Reactions: – – Remedy: Check unloader. Program Continuation:…

Sinumerik Alarm 104023 Error during tool loading Definitions: An error occurred while a tool was being loaded; the procedure has been aborted. Reactions: – – Remedy: Check loader. Program Continuation:…

Sinumerik Alarm 104020 No empty location found Definitions: There is no empty location with the specified search parameters. Reactions: – – Remedy: Correct search parameters. Program Continuation: Internal

Sinumerik Alarm 104019 Tool type not available Definitions: The specified tool type does not exist. Reactions: – – Remedy: Specify a valid tool type. Program Continuation: Internal

Sinumerik Alarm 104018 Tool not available Definitions: The specified tool does not exist. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 104016 No spindle available Definitions: No spindle was configured. Reactions: – – Remedy: Configure a spindle via the machine data. Program Continuation: Internal

Sinumerik Alarm 104015 Number of parameters per cutting edge is zero Definitions: The number of parameters per cutting edge was not configured. Reactions: – – Remedy: Configure the number of…

Sinumerik Alarm 104014 Incorrect entry Definitions: The entered value is impermissible, e.g., it lies outside the input limits. Reactions: – – Remedy: Please observe the value range. Program Continuation: Internal

Sinumerik Alarm 104012 No master spindle available Definitions: No master spindle was configured. Reactions: – – Remedy: Configure a master spindle via the machine data. Program Continuation: Internal

Sinumerik Alarm 104011 Error during tool deletion Definitions: The tool cannot be deleted. It may currently be active. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 104008 Error during cutting edge creation Definitions: No new cutting edge could be created, as, for example, the maximum number of cutting edges has already been reached. Reactions:…

Sinumerik Alarm 104007 Error during tool creation Definitions: The tool could not be created, as, for example, the maximum number of possible tools has already been reached. Reactions: – –…

Sinumerik Alarm 104006 No TO area available in the current channel Definitions: No TO area is assigned to the current channel. Reactions: – – Remedy: Assign the current channel a…

Sinumerik Alarm 104005 No cutting edge selected Definitions: A tool has been selected, but not a cutting edge. Reactions: – – Remedy: Select a cutting edge. Program Continuation: Internal