Sinumerik Alarms

Sinumerik Alarm 104004 No tool selected Definitions: After pressing the soft key “Current T+D No.” in the “Tool overview” window, no tool was found because no subroutine is active or…

Sinumerik Alarm 104003 There aren’t any tools at all Definitions: No tools were set up. Reactions: – – Remedy: Set up tools. Program Continuation: Internal

Sinumerik Alarm 104002 No other cutting edges available Definitions: After pressing the soft key “D No. +” or “D No. -” the next-highest or next-lowest cutting edge is searched for….

Sinumerik Alarm 104001 No other tools available Definitions: After pressing the soft key “T No. +” or “T No. -” the next-highest or next-lowest tool number is searched for. If…

Sinumerik Alarm 104000 Current tool not found Definitions: If the cursor in the window “Magazine list” is at a blank line, then no tool will be found after pressing the…

Sinumerik Alarm 103014 Please reference the axis first Definitions: The reference point approach was not yet performed or finished. Reactions: – – Remedy: Perform reference point approach. Program Continuation: Internal

Sinumerik Alarm 103011 No program selected – block search finished Definitions: At the moment, no program is selected, therefore, no search run is possible. Reactions: – – Remedy: Select a…

Sinumerik Alarm 103010 Invalid file name Definitions: The file name entered: • Must not have more than 32 characters (letters, digits, underscore; including the block and program ID:_N_ and _MPF),…

Sinumerik Alarm 103009 Conflict between search type and search target! Definitions: • The search target entered is not compatible with the search type: • The block number initial character “N”…

Sinumerik Alarm 103008 Block search in channel %1 started – please wait Parameters: %1 = Channel number Definitions: The started block search is not yet finished. Reactions: – – Remedy:…

Sinumerik Alarm 103007 Ending overstore is not possible in this channel state. Definitions: Overstore cannot be ended because the channel is still active. Reactions: – – Remedy: Wait until the…

Sinumerik Alarm 103006 Block search without calculation only possible on the main program level. Definitions: No subroutine calls can be processed during a block search without calculation. Reactions: – –…

Sinumerik Alarm 103004 Block search not possible Definitions: The search run cannot be started because the channel is active. Reactions: – – Remedy: Wait until the program has been executed…

Sinumerik Alarm 103003 MDI clipboard cannot be deleted Definitions: The NCK rejects a deletion of the clipboard because the clipboard is currently being executed. Reactions: – – Remedy: Wait until…

Sinumerik Alarm 103002 Copying to the clipboard is not possible Definitions: The NCK rejects a copy-action to the clipboard because, for example, no more memory is available or the maximum…

Sinumerik Alarm 103001 Selection is only possible after being enabled or in the RESET state. Definitions: In order to execute the desired function, the current channel has to be in…

Sinumerik Alarm 103000 There is no correction block on the NCK Definitions: The following is valid up to SW 3.x: The correction block window cannot be opened. No program correction…

Sinumerik Alarm 101300 Please wait – language is being changed Definitions: In the start-up area the soft key “Change language” was pressed. The screen content is being restructured. Reactions: –…

Sinumerik Alarm 101214 Initialization of this window failed! Definitions: An attempt was made to select the image of the NCK address in the start-up area. An error occured while determining…

Sinumerik Alarm 101213 Invalid NCK address. Definitions: The value specified for the new NCK bus address is too large. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 101212 NCK address changed! Definitions: The NCK’s bus address was set to the specified value. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 101211 NCK address not changed! Definitions: An attempt was made to change the bus address of the NCK in the start-up area. The change was rejected by the…

Sinumerik Alarm 101210 The machine data is being prepared for display Definitions: A list image in the machine data was selected for which display options are active. This image’s machine…

Sinumerik Alarm 101209 SI data confirmed: Drive 1 Definitions: In the start-up area the function “Confirm Safety Integrated Data” has been started. The message was output during this function in…

Sinumerik Alarm 101208 SI data confirmed: Axis 1 Definitions: In the start-up area the function “Confirm Safety Integrated Data” has been started. The message was output during this function in…

Sinumerik Alarm 101207 Position at $MN_ Definitions: A list image, e.g. general machine data, was selected. The MMC100 attempts to position at the datum selected last in this image. Reactions:…

Sinumerik Alarm 101206 Search action running, pleas wait Definitions: The search function was initiated in the machine data images. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 101205 Drive data changed? -> Don’t forget to save the boot files! Definitions: When exiting the drive machine data images, the operator is reminded to save the boot…

Sinumerik Alarm 101204 SI data not confirmed Definitions: The SI data confirmation function was not executed because an error occurred during the processing. Reactions: – – Remedy: – Program Continuation:…

Sinumerik Alarm 101203 SI data not completely copied Definitions: An error occurred during the SI data copying function; this caused the SI data to be copied incompletely or not at…

Sinumerik Alarm 101202 SI data is copied from axis %1 to drive %2 Parameters: %1 = Axis name %2 = Drive number Definitions: This message is output during the SI…

Sinumerik Alarm 101201 Safety-Integrated data confirmed Definitions: The SI data confirmation function was successful. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 101200 Safety-Integrated data copied Definitions: The SI data copying function was successful. Reactions: – – Remedy: – Program Continuation: Internal

Sinumerik Alarm 101161 The drive is not in cyclic mode! Definitions: The start-up is not completely carried out, therefore, the function “Calculate motor data” cannot be selected. Reactions: – –…

Sinumerik Alarm 101160 Date and time of the PLC set Definitions: In the PLC status, the time or date was changed. Reactions: – – Remedy: – Program Continuation: Internal