Sinumerik Alarms

Sinumerik Alarm 61249 Channel %1 block %2: Number of edges too small Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface signals are set….

Sinumerik Alarm 61248 Channel %1 block %2: Infeed too small Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface signals are set. – Alarm…

Sinumerik Alarm 61247 Channel %1 block %2: Blank radius too small Parameters: %1 = Channel number %2 = Block number, label Definitions: – Reactions: – Interpreter stop – NC Start…

Sinumerik Alarm 61246 Channel %1 block %2: Safety clearance too small Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface signals are set. –…

Sinumerik Alarm 61244 Channel %1 block %2: Thread lead change results in an undefined thread Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface…

Sinumerik Alarm 61243 Channel %1 block %2: Correct tool change point, tool tip is in retraction area! Definitions: The tool change point has to be far enough outside the retraction…

Sinumerik Alarm 61241 Channel %1 block %2: No retraction plane defined for this machining direction. Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface…

Sinumerik Alarm 61240 Channel %1 block %2: Wrong feed type Definitions: – Reactions: – Interpreter stop – NC Start disable in this channel. – Interface signals are set. – Alarm…

Sinumerik Alarm 61239 Channel %1 block %2: Tool change point lies in the retraction area! Definitions: The tool change point has to be far enough outside the retraction area so…

Sinumerik Alarm 61238 Channel %1 block %2: Machining direction unknown. Parameters: %1 = Channel number %2 = Block number, label Definitions: – Reactions: – Interpreter stop – NC Start disable…

Sinumerik Alarm 61237 Channel %1 block %2: Retraction direction unknown. Manually retract tool! Parameters: %1 = Channel number %2 = Block number, label Definitions: – Reactions: – Interpreter stop –…

Sinumerik Alarm 61236 Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn. Parameters: %1 = Channel number %2 = Block number,…

Sinumerik Alarm 61235 Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn. Parameters: %1 = Channel number %2 = Block number,…

Sinumerik Alarm 61234 Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill Parameters: %1 = Channel number %2 = Block number,…

Sinumerik Alarm 61233 Channel %1 block %2: Thread inclination incorrectly defined Parameters: %1 = Channel number %2 = Block number, label Definitions: – Reactions: – Interpreter stop – NC Start…

Sinumerik Alarm 61232 Channel %1 block %2 loading of magazine tool not possible Parameters: %1 = Channel number %2 = Block number, label Definitions: Only manual tools may be loaded…

Sinumerik Alarm 61231 Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill Parameters: %1 = Channel number %2 = Block number,…

Sinumerik Alarm 61230 Channel %1 block %2 tool probe diameter too small Parameters: %1 = Channel number %2 = Block number, label Definitions: The tool probe is not correctly calibrated….

Sinumerik Alarm 61226 Channel %1 block %2 swivel head cannot be exchanged Parameters: %1 = Channel number %2 = Block number, label Definitions: The parameter “Swivel data block” is set…

Sinumerik Alarm 61225 Channel %1 block %2 swivel data block unknown Parameters: %1 = Channel number %2 = Block number, label Definitions: An attempt was made to access a swivel…

Sinumerik Alarm 61224 Channel %1 block %2 retract path too short Parameters: %1 = Channel number %2 = Block number, label Definitions: The retract path must not be less than…

Sinumerik Alarm 61223 Channel %1 block %2 approach path too short Parameters: %1 = Channel number %2 = Block number, label Definitions: The approach path must not be less than…

Sinumerik Alarm 61222 Channel %1 block %2 plane infeed greater than the tool diameter Parameters: %1 = Channel number %2 = Block number, label Definitions: The plane infeed must not…

Sinumerik Alarm 61218 Channel %1 block %2 feed/tooth programmed, but number of teeth is zero Parameters: %1 = Channel number %2 = Block number, label Definitions: For feed per tooth,…

Sinumerik Alarm 61217 Channel %1 block %2 cutting speed for tool radius 0 programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: To be able to work…

Sinumerik Alarm 61216 Channel %1 block %2 feed/tooth only possible with milling tools Parameters: %1 = Channel number %2 = Block number, label Definitions: Feed per tooth is only possible…

Sinumerik Alarm 61215 Channel %1 block %2 raw dimension incorrectly programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycle: CYCLE76, CYCLE77. Reactions:…

Sinumerik Alarm 61214 Channel %1 block %2 no lead programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: No thread lead was entered. Alarm triggered by following…

Sinumerik Alarm 61213 Channel %1 block %2 circle radius too small Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycle: CYCLE77. Reactions: –…

Sinumerik Alarm 61212 Channel %1 block %2 wrong tool type Parameters: %1 = Channel number %2 = Block number, label Definitions: The tool type is not suitable for machining. Alarm…

Sinumerik Alarm 61211 Channel %1 block %2 absolute reference missing Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: CYCLE76, CYCLE77. Reactions: –…

Sinumerik Alarm 61210 Channel %1 block %2 block search element not found Parameters: %1 = Channel number %2 = Block number, label Definitions: The element specified for the block search…

Sinumerik Alarm 61205 Channel %1 block %2 unknown positioning cycle Parameters: %1 = Channel number %2 = Block number, label Definitions: The specified positioning cycle in the machining block is…

Sinumerik Alarm 61204 Channel %1 block %2 unknown technology cycle Parameters: %1 = Channel number %2 = Block number, label Definitions: The specified technology cycle in the machining block is…

Sinumerik Alarm 61203 Channel %1 block %2 no positioning cycle Parameters: %1 = Channel number %2 = Block number, label Definitions: No positioning cycle was programmed in the machining block….