Sinumerik Alarms

Sinumerik Alarm 61102 Channel %1 block %2 no spindle direction programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: CYCLE86, CYCLE87, CYCLE88,…

Sinumerik Alarm 61101 Channel %1 block %2 reference plane incorrectly defined Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: CYCLE71, CYCLE72, CYCLE81…

Sinumerik Alarm 61013 Channel %1 block %2 basic settings were changed, program cannot be executed Parameters: %1 = Channel number %2 = Block number, label channel number Definitions: The basic…

Sinumerik Alarm 61012 Channel %1 block %2 different scaling on the plane Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: CYCLE76, CYCLE77….

Sinumerik Alarm 61011 Channel %1 block %2 scaling not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: A scale factor is active which is illegal for…

Sinumerik Alarm 61010 Channel %1 block %2 finishing allowance too large Parameters: %1 = Channel number %2 = Block number, label Definitions: The finishing allowance for the base is greater…

Sinumerik Alarm 61009 Channel %1 block %2 active tool number = 0 Parameters: %1 = Channel number %2 = Block number, label Definitions: No tool (T) has been programmed before…

Sinumerik Alarm 61007 Channel %1 block %2 tool radius too small Parameters: %1 = Channel number %2 = Block number, label Definitions: The tool radius is too small for machining….

Sinumerik Alarm 61006 Channel %1 block %2 tool radius too large Parameters: %1 = Channel number %2 = Block number, label Definitions: The tool radius is too large for machining….

Sinumerik Alarm 61005 Channel %1 block %2 3rd geometry axis not present Parameters: %1 = Channel number %2 = Block number, label Definitions: With an application on the lathe with…

Sinumerik Alarm 61004 Channel %1 block %2 configuration geometry axis incorrect Parameters: %1 = Channel number %2 = Block number, label Definitions: The geometry-axes sequence is wrong. CYCLE328 Reactions: –…

Sinumerik Alarm 61003 Channel %1 block %2 no feed programmed in the cycle Parameters: %1 = Channel number %2 = Block number, label Definitions: The parameter for the feed has…

Sinumerik Alarm 61002 Channel %1 block %2 machining type wrongly defined Parameters: %1 = Channel number %2 = Block number, label Definitions: The value of the VARI parameter for the…

Sinumerik Alarm 61001 Channel %1 block %2 thread lead incorrect Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: CYCLE84, CYCLE840, CYCLE96, CYCLE97….

Sinumerik Alarm 61000 Channel %1 block %2 no tool compensation active Parameters: %1 = Channel number %2 = Block number, label Definitions: Alarm triggered by following cycles: LONGHOLE, SLOT1, SLOT2,…

Sinumerik Alarm 60000 Channel %1 block %2: Parameters: %1 = Channel number %2 = Block number, label Definitions: – Reactions: – Alarm display. – Interface signals are set. – NC…

Sinumerik Alarm 29033 Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed Parameters: %1 = Channel number %2 = Axis Definitions: A PLC axis…

Sinumerik Alarm 28033 Emergency stop on NCU % 1, axes still in follow-up mode Parameters: %1 = NCU number Definitions: The emergency stop request is active at the PLC-NCK interface…

Sinumerik Alarm 28032 Emergency stop activated on NCU %1, axes in follow-up mode Parameters: %1 = NCU number Definitions: The emergency stop request is active at the PLC-NCK interface on…

Sinumerik Alarm 28031 Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode Parameters: %1 = NCU number Definitions: A serious alarm was not yet acknowledged on…

Sinumerik Alarm 28030 Serious alarm on NCU %1, axes in follow-up mode Parameters: %1 = NCU number Definitions: All axes are trailing because of a serious alarm on another NCU….

Sinumerik Alarm 28020 NCU link: too many link axes configured %1 Parameters: %1 = Number of link axis connections Definitions: Unfortunately, the communication capacity of the NCU link is insufficient…

Sinumerik Alarm 28012 NCU link: synchronization cycle signal failure %1 times Parameters: %1 = Number of cycles Definitions: Error message of the NCU link module that does not occur at…

Sinumerik Alarm 28011 IPO time insufficient for NCU link. Link cycle time: %1 Parameters: %1 = Microseconds Definitions: Error message of the NCU link module. All messages must be transmitted…

Sinumerik Alarm 28010 NCU link: the NCU %1 has not received a message Parameters: %1 = NCU number Definitions: Error message of the NCU link module. During operation of the…

Sinumerik Alarm 28009 NCU link: conflict in bus parameters of NCU %1 Parameters: %1 = NCU number Definitions: Error message of the NCU link module. When the NCU link was…

Sinumerik Alarm 28008 NCU link: conflict in timer setting of NCU %1 Parameters: %1 = NCU number Definitions: Error message of the NCU link module. When the NCU link was…

Sinumerik Alarm 28007 NCU link: conflict in configuration data of NCU %1 Parameters: %1 = NCU number Definitions: Error message of the NCU link module. When the NCU link was…

Sinumerik Alarm 28005 NCU link: NCU %1 of the link network not running synchronously Parameters: %1 = NCU number Definitions: Error message of the NCU link module. When the NCU…

Sinumerik Alarm 28002 Error on activation of machine data, NCU network-wide machine data were modified by NCU %1 Parameters: %1 = NCU number Definitions: During the activation of machine data…

Sinumerik Alarm 28001 NCU link connection to the NCU %1 of the link network has been aborted Parameters: %1 = NCU number Definitions: All NCUs in the NCU link network…

Sinumerik Alarm 28000 NCU link connection to all other NCUs of the link network has been aborted Definitions: All NCUs in the NCU link network exchange data cyclically (sign-of-life). If…

Sinumerik Alarm 27299 PROFIsafe: Diagnosis %1 %2 %3 %4 Parameters: %1 = Error code 1 %2 = Error code 2 %3 = Error code 3 %4 = Error code 4…

Sinumerik Alarm 27256 PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time Parameters: %1 = Current PROFIsafe communication cycle time Definitions: The current PROFIsafe communication cycle time is greater…

Sinumerik Alarm 27255 PROFIsafe: F module %1, general error Parameters: %1 = PROFIsafe address Definitions: The specified PROFIsafe module signals an error. A more exact specification of the error’s cause…