Sinumerik Alarms

Sinumerik Alarm 27034 Parameterization of MD %1 invalid Parameters: %1 = MD identifier Definitions: The parameterization of %1 is incorrect. This alarm occurs in the following context: an incorrect value…

Sinumerik Alarm 27033 Axis %1 parameterization of MD %2[%3] invalid Parameters: %1 = Axis number %2 = MD identifier %3 = Machine data index Definitions: The parameterization of %2 is…

Sinumerik Alarm 27032 Axis %1 checksum error of safe monitoring. Confirmation and re-test required! Parameters: %1 = Axis number Definitions: The machine data “MA_SAFE_…” are protected by a checksum after…

Sinumerik Alarm 27031 Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4) Parameters: %1 = Axis number %2 = Limit value index %3…

Sinumerik Alarm 27030 Axis %1 function not supported on this 611D module Parameters: %1 = Axis number Definitions: SINUMERIK Safety Integrated can be used only with the 611D Performance control…

Sinumerik Alarm 27024 Axis %1 stop A triggered Parameters: %1 = Axis number Definitions: This alarm comes with the alarm 27011 “Safe velocity exceeded” (when configured as such in $MA_SAFE_VELO_STOP_MODE)…

Sinumerik Alarm 27023 Axis %1 stop B triggered Parameters: %1 = Axis number Definitions: This alarm comes with the alarm 27010 “Tolerance for safe standstill exceeded” or 27001 “STOP F…

Sinumerik Alarm 27022 Axis %1 stop C triggered Parameters: %1 = Axis number Definitions: This alarm comes with the alarms 27011 “Safe velocity exceeded” or 27012 “Safe end position exceeded”…

Sinumerik Alarm 27021 Axis %1 stop D triggered Parameters: %1 = Axis number Definitions: This alarm comes with the alarms 27011 “Safe velocity exceeded” or 27012 “Safe end position exceeded”…

Sinumerik Alarm 27020 Axis %1 stop E triggered Parameters: %1 = Axis number Definitions: This alarm comes with the alarms 27011 “Safe velocity exceeded” or 27012 “Safe end position exceeded”…

Sinumerik Alarm 27013 Axis %1 safe braking ramp exceeded Parameters: %1 = Axis number Definitions: After the initiation of STOP B or C, the velocity exceeded the tolerance value entered…

Sinumerik Alarm 27012 Axis %1 safe end position exceeded Parameters: %1 = Axis number Definitions: The axis has exceeded the limit position entered in MD $MA_SAFE_POS_LIMT_PLUS or MD $MA_SAFE_POS_LIMIT_MINUS. Stop…

Sinumerik Alarm 27011 Axis %1 safe velocity exceeded Parameters: %1 = Axis number Definitions: The axis has moved too quickly and faster than allowed in MD $MA_SAFE_VELO_LIMIT. With active SBH/SG…

Sinumerik Alarm 27010 Axis %1 tolerance for safe standstill exceeded Parameters: %1 = Axis number Definitions: The axis has moved too far away from the setpoint position. It is further…

Sinumerik Alarm 27008 Axis %1 SW limit switch deactivated Parameters: %1 = Axis number Definitions: Via the operator panel, an SI acceptance test safe end position has been started with…

Sinumerik Alarm 27007 Axis %1 acceptance test mode is active Parameters: %1 = Axis number Definitions: Via the operator panel, an SI acceptance test has been started with the acceptance…

Sinumerik Alarm 27006 Axis %1 Test ext. pulse deletion running Parameters: %1 = Axis number Definitions: The correct functioning of the external pulse disable is being checked now by setting…

Sinumerik Alarm 27005 Axis %1 error in data cross check: static actual value difference Parameters: %1 = Axis number Definitions: Via the data cross check between NCK and 611D monitoring…

Sinumerik Alarm 27004 Axis %1, difference safe input %2, NCK %3, drive %4 Parameters: %1 = Axis number %2 = Monitoring input %3 = Interface identifier NCK input %4 =…

Sinumerik Alarm 27003 Checksum error found: %1 %2 Parameters: %1 = Note on code section or table %2 = Table number Definitions: Checksum error in safety-relevant code or safety-relevant data….

Sinumerik Alarm 27002 Axis %1 test stop is running Parameters: %1 = Axis number Definitions: Proper functioning of the switch-off path is just being tested by setting of the SGE…

Sinumerik Alarm 27001 Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4 Parameters: %1 = Axis number %2 = Additional info cross-comparison index %3 =…

Sinumerik Alarm 27000 Axis %1 is not safely referenced Parameters: %1 = Axis number Definitions: There are two reasons for this alarm: • the machine position has not yet been…

Sinumerik Alarm 26110 Independent drive stop/retract triggered Definitions: Informational alarm: An “independent extended stop or retract” was triggered on the drive bus for at least one axis. The drive in…

Sinumerik Alarm 26106 Encoder %2 of axis %1 not found Parameters: %1 = Axis name, spindle number %2 = Encoder number Definitions: The drive configured for the specified axis could…

Sinumerik Alarm 26105 Drive of axis %1 not found Parameters: %1 = Axis name, spindle number Definitions: The drive configured for the specified axis could not be found. For example,…

Sinumerik Alarm 26102 Axis %1 drive %2 sign of life missing Parameters: %1 = Axis name, spindle number %2 = Drive number Definitions: The sign-of-life cell is no longer being…

Sinumerik Alarm 26101 Axis %1 drive %2 communication failure Parameters: %1 = Axis name, spindle number %2 = Drive number Definitions: The drive is not communicating. Reactions: – Mode group…

Sinumerik Alarm 26100 Axis %1 drive %2 sign of life missing Parameters: %1 = Axis name, spindle number %2 = Drive number Definitions: The sign-of-life cell is no longer being…

Sinumerik Alarm 26081 Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled Parameters: %1 = Channel %2 = Axis, spindle Definitions: The axis trigger…

Sinumerik Alarm 26080 Channel %1 retraction position of axis %2 not programmed or invalid Parameters: %1 = Channel %2 = Axis, spindle Definitions: No retraction position has been programmed for…

Sinumerik Alarm 26074 Channel %1 switching off PLC control of axis %2 not allowed in the current state Parameters: %1 = Channel %2 = Axis, spindle Definitions: The PLC can…

Sinumerik Alarm 26072 Channel %1 axis %2 cannot be controlled by the PLC Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: Axis cannot be made a…

Sinumerik Alarm 26070 Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: An attempt…

Sinumerik Alarm 26052 Channel %1 in block %2: path velocity too high for auxiliary function output Parameters: %1 = Channel number %2 = Block number, label Definitions: This alarm usually…