Sinumerik Alarms

Sinumerik Alarm 26051 Channel %1 in block %2 unanticipated stop crossed in continuous path mode Parameters: %1 = Channel number %2 = Block number, label Definitions: The path interpolation did…

Sinumerik Alarm 26050 Axis %1 parameter set change from %2 to %3 not possible Parameters: %1 = Axis name, spindle number %2 = Index: current parameter block %3 = Index:…

Sinumerik Alarm 26032 Axis %1 master-slave not configured Parameters: %1 = Axis name, spindle number Definitions: The master-slave coupling could not be activated because of incomplete configuration. Reactions: – Alarm…

Sinumerik Alarm 26031 Axis %1 configuration error master-slave Parameters: %1 = Axis name, spindle number Definitions: The alarm is output when the same machine axis has been configured as a…

Sinumerik Alarm 26030 Axis %1 encoder %2 absolute position lost Parameters: %1 = Axis name, spindle number %2 = Encoder number Definitions: The absolute position of the absolute encoder has…

Sinumerik Alarm 26025 Axis %1 machine data %2[%3] value changed Parameters: %1 = Axis name, spindle number %2 = String: MD identifier %3 = Index: MD array index Definitions: Machine…

Sinumerik Alarm 26024 Axis %1 machine data %2 value changed Parameters: %1 = Axis name, spindle number %2 = String: MD identifier Definitions: Machine data contains an invalid value and…

Sinumerik Alarm 26022 Axis %1 encoder %2 measurement with simulated encoder not possible Parameters: %1 = NC axis number %2 = Encoder number Definitions: Alarm occurs on the control when…

Sinumerik Alarm 26020 Axis %1 encoder %2 hardware fault %3 during encoder initialization Parameters: %1 = Axis name, spindle number %2 = Encoder number %3 = Error fine coding Definitions:…

Sinumerik Alarm 26019 Axis %1 encoder %2 measurement not possible with this controller module Parameters: %1 = NC axis number %2 = Encoder number Definitions: If the MD $MN_DRIVE_DIAGNOSIS[8] contains…

Sinumerik Alarm 26018 Axis %1 setpoint output drive %2 used more than once Parameters: %1 = Axis name, spindle number %2 = Drive number Definitions: A setpoint has been selected…

Sinumerik Alarm 26017 Axis %1 machine data %2[%3] invalid value Parameters: %1 = Axis name, spindle number %2 = String: MD identifier %3 = Index: MD array index Definitions: Machine…

Sinumerik Alarm 26016 Axis %1 machine data %2 invalid value Parameters: %1 = Axis name, spindle number %2 = String: MD identifier Definitions: Machine data includes a value that is…

Sinumerik Alarm 26014 Axis %1 machine data %2 invalid value Parameters: %1 = Axis name, spindle number %2 = String: MD identifier Definitions: Machine data includes a value that is…

Sinumerik Alarm 26015 Axis %1 machine data %2[%3] invalid value Parameters: %1 = Axis name, spindle number %2 = String: MD identifier %3 = Index: MD array index Definitions: Machine…

Sinumerik Alarm 26011 Axis %1 QEC: invalid measuring periods Parameters: %1 = Axis name, spindle number Definitions: $AA_QEC_MEAS_TIME_1/2/3: measuring time to determine the error criterion. The measuring period begins when…

Sinumerik Alarm 26010 Axis %1 QEC: invalid acceleration characteristic Parameters: %1 = Axis name, spindle number Definitions: $AA_QEC_ACCEL_1/2/3: The acceleration characteristic is divided into three areas. In each area there…

Sinumerik Alarm 26009 Axis %1 QEC: memory overflow Parameters: %1 = Axis name, spindle number Definitions: The product of the data $AA_QEC_COARSE_STEPS+1 and $AA_QEC_FINE_STEPS must not exceed the maximum number…

Sinumerik Alarm 26008 Axis %1 QEC: invalid fine step size Parameters: %1 = Axis name, spindle number Definitions: The fine step size for quadrant error compensation must be in the…

Sinumerik Alarm 26007 Axis %1 QEC: invalid coarse step size Parameters: %1 = Axis name, spindle number Definitions: The course step width for QEC must be within the range 1

Sinumerik Alarm 26006 Axis %1 encoder %2 encoder type/output type %3 not possible Parameters: %1 = Axis name, spindle number %2 = Encoder number %3 = Encoder type/output type Definitions:…

Sinumerik Alarm 26005 Axis %1 parameterization error: output rating Parameters: %1 = Axis name, spindle number Definitions: The output evaluation of the analog speed setpoint set in the machine data…

Sinumerik Alarm 26004 Axis %1 encoder %2 parameterization error: grid point distance with linear encoders Parameters: %1 = Axis name, spindle number %2 = Encoder number Definitions: The encoder grid…

Sinumerik Alarm 26003 Axis %1 parameterization error: lead screw pitch Parameters: %1 = Axis name, spindle number Definitions: The pitch of the ballscrew/trapezoidal leadscrew set in the axis-specific machine data…

Sinumerik Alarm 26002 Axis %1 encoder %2 parameterization error: number of encoder marks Parameters: %1 = Axis name, spindle number %2 = Encoder number Definitions: 1. Rotary measuring system ($MA_ENC_IS_LINEAR[]==FALSE)…

Sinumerik Alarm 26001 Axis %1 parameterization error: friction compensation Parameters: %1 = Axis name, spindle number Definitions: The parameterization of the adaptation characteristic in the quadrant error compensation is not…

Sinumerik Alarm 26000 Axis %1 clamping monitoring Parameters: %1 = Axis name, spindle number Definitions: The clamped axis is to be pushed out of its setpoint position. The permissible difference…

Sinumerik Alarm 25202 Axis %1 waiting for drive Parameters: %1 = Axis name, spindle number Definitions: Drive group error (self-clearing). Reactions: – Alarm display. – Interface signals are set. Remedy:…

Sinumerik Alarm 25201 Axis %1 drive fault Parameters: %1 = Axis name, spindle number Definitions: The drive signals a serious fault of status class 1 (ZK1). The exact cause of…

Sinumerik Alarm 25200 Axis %1 requested set of parameters invalid Parameters: %1 = Axis name, spindle number Definitions: A new parameter set has been requested for the positioning control. The…

Sinumerik Alarm 25110 Axis %1 selected encoder not available Parameters: %1 = Axis name, spindle number Definitions: The selected encoder does not correspond to the maximum number of encoders in…

Sinumerik Alarm 25105 Axis %1 measuring systems differ considerably Parameters: %1 = Axis name, spindle number Definitions: The two measuring systems differ considerably, i.e. the cyclically monitored actual value difference…

Sinumerik Alarm 25100 Axis %1 measuring system switchover not possible Parameters: %1 = Axis name, spindle number Definitions: The prerequisites are not satisfied for the required encoder switchover: 1. The…

Sinumerik Alarm 25080 Axis %1 positioning monitoring Parameters: %1 = Axis name, spindle number Definitions: For blocks in which “exact stop” is effective, the axis must have reached the exact…

Sinumerik Alarm 25070 Axis %1 drift value too large Parameters: %1 = Axis name, spindle number Definitions: Only in FM-NC with analog drives! The permissible maximum value of drift (internal,…