Sinumerik Alarms

Sinumerik Alarm 25050 Axis %1 contour monitoring Parameters: %1 = Axis name, spindle number Definitions: The NCK calculates for each interpolation point (setpoint) of an axis the actual value that…

Sinumerik Alarm 25042 Axis %1 standstill monitoring during torque/force limitation Parameters: %1 = Axis name, spindle number Definitions: The defined end position was not reached within the time specified in…

Sinumerik Alarm 25040 Axis %1 standstill monitoring Parameters: %1 = Axis name, spindle number Definitions: The NC monitors to ensure that the position is held at zero speed. Monitoring is…

Sinumerik Alarm 25031 Axis %1 actual velocity warning limit Parameters: %1 = Axis name, spindle number Definitions: The present velocity actual value is more than 80% of the limit value…

Sinumerik Alarm 25030 Axis %1 actual velocity alarm limit Parameters: %1 = Axis name, spindle number Definitions: If the axis has at least one active encoder, then the actual speed…

Sinumerik Alarm 25022 Axis %1 encoder %2 warning %3 Parameters: %1 = Axis name, spindle number %2 = Encoder number %3 = Error fine coding Definitions: This alarm occurs only…

Sinumerik Alarm 25021 Axis %1 zero mark monitoring of passive encoder Parameters: %1 = Axis name, spindle number Definitions: Monitoring relates to the encoder that is not used by the…

Sinumerik Alarm 25020 Axis %1 zero mark monitoring of active encoder Parameters: %1 = Axis name, spindle number Definitions: The position encoder pulses between 2 zero marker pulses are counted…

Sinumerik Alarm 25011 Axis %1 pollution of passive encoder Parameters: %1 = Axis name, spindle number Definitions: The encoder not used for position control sends a contamination signal (only in…

Sinumerik Alarm 25001 Axis %1 hardware fault of passive encoder Parameters: %1 = Axis name, spindle number Definitions: The signals from the position actual value encoder that is presently not…

Sinumerik Alarm 25000 Axis %1 hardware fault of active encoder Parameters: %1 = Axis name, spindle number Definitions: The signals of the currently active position actual value encoder (interface signal…

Sinumerik Alarm 22322 Channel %1 axis %2 PRESET: illegal value Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: The entered Preset value is too large (number…

Sinumerik Alarm 22321 Channel %1 axis %2 PRESET not allowed during traverse motion Parameters: %1 = Channel number %2 = Block number, label Definitions: A preset command was given from…

Sinumerik Alarm 22320 Channel %1 block %2 PUTFTOCF command could not be transferred Parameters: %1 = Channel number %2 = Block number, label Definitions: The cyclic transfer of the PUTFTOCF…

Sinumerik Alarm 22280 Channel %1 in block %2: Prog. acceleration path too short %3, %4 required Parameters: %1 = Channel number %2 = Block number, label %3 = Prog. acceleration…

Sinumerik Alarm 22275 Channel %1 block %2 zero velocity of thread axis at position %3 reached Parameters: %1 = Channel number %2 = Block number, label %3 = Position Definitions:…

Sinumerik Alarm 22270 Channel %1 block %2 maximum velocity of thread axis at position %3 reached Parameters: %1 = Channel number %2 = Block number, label %3 = Position Definitions:…

Sinumerik Alarm 22260 Channel %1 spindle %2 thread might be damaged Parameters: %1 = Channel number %2 = Axis name %3 = Block number Definitions: When DECODING SINGLE BLOCK has…

Sinumerik Alarm 22250 Channel %1 spindle %2 axis stopped during thread cutting Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: The thread cutting axis has been…

Sinumerik Alarm 22200 Channel %1 spindle %2 axis stopped during tapping Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: When tapping with compensating chuck (G63) the…

Sinumerik Alarm 22100 Channel %1 block %3 spindle %2 chuck speed exceeded Parameters: %1 = Channel number %2 = Axis name, spindle number %3 = Block number, label Definitions: The…

Sinumerik Alarm 22071 TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration Parameters: %1 = TO unit %2 = Tool identifier…

Sinumerik Alarm 22070 TO unit %1 Please change tool T= %2 into magazine. Repeat data backup Parameters: %1 = TO unit %2 = T number of tool Definitions: The alarm…

Sinumerik Alarm 22069 Channel %1 block %2 tool management: No tool available in tool group %3, program %4 Parameters: %1 = Channel number %2 = Block number, label %3 =…

Sinumerik Alarm 22068 Channel %1 block %2 tool management: no tool available in tool group %3 Parameters: %1 = Channel number %2 = Block number, label %3 = String (identifier)…

Sinumerik Alarm 22067 Channel %1 tool management: tool change not possible since there is no tool available in tool group %2 Parameters: %1 = Channel number %2 = String (identifier)…

Sinumerik Alarm 22066 Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 Parameters: %1 = Channel number %2…

Sinumerik Alarm 22065 Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 Parameters: %1 = Channel number %2…

Sinumerik Alarm 22064 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions:…

Sinumerik Alarm 22062 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions:…

Sinumerik Alarm 22060 Channel %1 position control expected for axis/spindle %2 Parameters: %1 = Channel number %2 = Axis name, spindle number Definitions: The programmed coupling type (DV, AV) or…

Sinumerik Alarm 22055 Channel %1 block %3 spindle %2 configured positioning speed is too high Parameters: %1 = Channel number %2 = Axis name, spindle number %3 = Block number,…

Sinumerik Alarm 22054 Channel %1 block %3 spindle %2 improper punching signal Parameters: %1 = Channel number %2 = Axis name, spindle number %3 = Block number, label Definitions: If…

Sinumerik Alarm 22053 Channel %1 block %3 spindle %2 reference mode not supported Parameters: %1 = Channel number %2 = Axis name, spindle number %3 = Block number, label Definitions:…

Sinumerik Alarm 22052 Channel %1 block %3 spindle %2 no standstill on block change Parameters: %1 = Channel number %2 = Axis name, spindle number %3 = Block number, label…