Sinumerik Alarms

Sinumerik Alarm 14602 Channel %1 block %2 timeout during EXTCALL Parameters: %1 = Channel number %2 = Block number, label Definitions: No connection could be established to the MMC for…

Sinumerik Alarm 14601 Channel %1 block %2 reload buffer could not be deleted Parameters: %1 = Channel number %2 = Block number, label Definitions: The reload buffer for “execute from…

Sinumerik Alarm 14600 Channel %1 block %2 reload buffer %3 cannot be established Parameters: %1 = Channel number %2 = Block number, label %3 = File name Definitions: The download…

Sinumerik Alarm 14530 Channel %1 block %2 EXTERN and PROC instruction do not correspond Parameters: %1 = Channel number %2 = Block number, label Definitions: Subroutines with parameter transfer must…

Sinumerik Alarm 14520 Channel %1 block %2 illegal PROC instruction in data definition section Parameters: %1 = Channel number %2 = Block number, label Definitions: The PROC statement may only…

Sinumerik Alarm 14510 Channel %1 block %2 PROC instruction missing on subroutine call Parameters: %1 = Channel number %2 = Block number, label Definitions: In subroutine calls with parameter transfer…

Sinumerik Alarm 14500 Channel %1 block %2 illegal DEF or PROC instruction in the part program Parameters: %1 = Channel number %2 = Block number, label Definitions: NC part programs…

Sinumerik Alarm 14420 Channel %1 block %2 index axis %3 frame not allowed Parameters: %1 = Channel number %2 = Block number, label %3 = Axis Definitions: The axis is…

Sinumerik Alarm 14415 Channel %1 block %2 tangent control: changeover geometry/channel axis not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: An assignment change of the…

Sinumerik Alarm 14414 Channel %1 block %2 GEOAX function: incorrect call Parameters: %1 = Channel number %2 = Block number, label Definitions: The parameters for the GEOAX(…) call are incorrect….

Sinumerik Alarm 14413 Channel %1 block %2 fine tool correction: changeover geometry/channel axis not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: It is not permissible…

Sinumerik Alarm 14412 Channel %1 block %2 transformation active at geometry axis changeover Parameters: %1 = Channel number %2 = Block number, label Definitions: It is not permissible to change…

Sinumerik Alarm 14411 Channel %1 block %2 tool radius compensation active at geometry axis changeover Parameters: %1 = Channel number %2 = Block number, label Definitions: It is not permissible…

Sinumerik Alarm 14410 Channel %1 block %2 spline active at geometry axis changeover Parameters: %1 = Channel number %2 = Block number, label Definitions: It is not allowed to change…

Sinumerik Alarm 14404 Channel %1 block %2 illegal parametrization of transformation Parameters: %1 = Channel number %2 = Block number, label Definitions: Error has occurred when selecting transformation.Possible causes of…

Sinumerik Alarm 14403 Channel %1 block %2 preprocessing and main run might not be synchronized Parameters: %1 = Channel number %2 = Block number, label Definitions: Positioning axis runs cannot…

Sinumerik Alarm 14402 Channel %1 block %2 spline active at transformation change Parameters: %1 = Channel number %2 = Block number, label Definitions: A change of transformation is not allowed…

Sinumerik Alarm 14401 Channel %1 block %2 transformation not available Parameters: %1 = Channel number %2 = Block number, label Definitions: The required transformation is not available. Reactions: – Alarm…

Sinumerik Alarm 14310 Handwheel %1 configuration incorrect or inactive Parameters: %1 = Handwheel number Definitions: • The inputs are using a drive with a drive number that does not exist…

Sinumerik Alarm 14400 Channel %1 block %2 tool radius compensation active at transformation switchover Parameters: %1 = Channel number %2 = Block number, label Definitions: A change of transformation is…

Sinumerik Alarm 14300 Channel %1 block %2 overlaid handwheel motion activated incorrectly Parameters: %1 = Channel number %2 = Block number, label Definitions: Handwheel override has been called up incorrectly:…

Sinumerik Alarm 14290 Channel %1 block %2 poly nominal degree greater than 5 programmed for poly nominal interpolation Parameters: %1 = Channel number %2 = Block number, label Definitions: A…

Sinumerik Alarm 14280 Channel %1 block %2 polar coordinates programmed incorrectly Parameters: %1 = Channel number %2 = Block number, label Definitions: The end point of the displayed block has…

Sinumerik Alarm 14270 Channel %1 block %2 pole programmed incorrectly Parameters: %1 = Channel number %2 = Block number, label Definitions: When defining the pole, an axis was programmed that…

Sinumerik Alarm 14260 Channel %1 block %2 pole angle too large Parameters: %1 = Channel number %2 = Block number, label Definitions: In redefining the pole with G110, G111 or…

Sinumerik Alarm 14250 Channel %1 block %2 negative pole radius Parameters: %1 = Channel number %2 = Block number, label Definitions: In redefining the pole with G110, G111 or G112…

Sinumerik Alarm 14210 Channel %1 block %2 polar angle too large Parameters: %1 = Channel number %2 = Block number, label Definitions: In specifying the endpoints in a traversing block…

Sinumerik Alarm 14200 Channel %1 block %2 negative polar radius Parameters: %1 = Channel number %2 = Block number, label Definitions: In the endpoint specification of a traversing block with…

Sinumerik Alarm 14199 Channel %1 block %2 illegal plane change for tool with diameter component Parameters: %1 = Channel number %2 = Block number, label Definitions: If a tool has…

Sinumerik Alarm 14198 Channel %1 block %2 illegal change of tool direction with tool offset Parameters: %1 = Channel number %2 = Block number, label Definitions: If an offset is…

Sinumerik Alarm 14197 Channel %1 block %2 D number and H number programmed simultaneously Parameters: %1 = Channel number %2 = Block number, label Definitions: A D word and H…

Sinumerik Alarm 14195 Channel %1 block %2 D number with G49 Parameters: %1 = Channel number %2 = Block number, label Definitions: G49 (select tool length compensation) and an D…

Sinumerik Alarm 14190 Channel %1 block %2 H number with G49 Parameters: %1 = Channel number %2 = Block number, label Definitions: G49 (select tool length compensation) and an H…

Sinumerik Alarm 14185 Channel %1 block %2 D number is not defined Parameters: %1 = Channel number %2 = Block number, label Definitions: The specified D number is not assigned…

Sinumerik Alarm 14180 Channel %1 block %2 H number is not defined Parameters: %1 = Channel number %2 = Block number, label Definitions: The specified H number is not assigned…