Sinumerik Alarms

Sinumerik Alarm 14170 Channel %1 block %2 illegal interpolation type with tool length compensation Parameters: %1 = Channel number %2 = Block number, label Definitions: If tool compensation (G43/G44) is…

Sinumerik Alarm 14165 Channel %1 block %2 active T number does not match selected tool Parameters: %1 = Channel number %2 = Block number, label Definitions: When an H or…

Sinumerik Alarm 14160 Channel %1 block %2 tool length selection without geometry axis specification Parameters: %1 = Channel number %2 = Block number, label Definitions: If variant C (tool length…

Sinumerik Alarm 14159 Channel %1 block %2 more than two angles programmed with ROTS or AROTS Parameters: %1 = Channel number %2 = Block number, label Definitions: Frame rotations are…

Sinumerik Alarm 14157 Channel %1 block %2 illegal interpolation type with MOVT Parameters: %1 = Channel number %2 = Block number, label Definitions: Linear or spline interpolation must be active…

Sinumerik Alarm 14156 Channel %1 toolholder selection error at reset Parameters: %1 = Channel number Definitions: The settings in RESET_MODE_MASK require that an active orientable toolholder is maintained after the…

Sinumerik Alarm 14155 Channel %1 block %2 invalid base frame definition for tool carrier offset Parameters: %1 = Channel number %2 = Block number, label Definitions: If a tool carrier…

Sinumerik Alarm 14154 Channel %1 block %2 The amount of fine correction in parameter %3 of the orientable tool holder %4 is too large Parameters: %1 = Channel number %2…

Sinumerik Alarm 14153 Channel %1 block %2 unknown tool carrier type: %3 Parameters: %1 = Channel number %2 = Block number, label %3 = Tool carrier type Definitions: An invalid…

Sinumerik Alarm 14152 Channel %1 block %2 tool carrier: invalid orientation. Error code: %3 Parameters: %1 = Channel number %2 = Block number, label %3 = Error code Definitions: An…

Sinumerik Alarm 14151 Channel %1 block %2 illegal tool carrier rotation Parameters: %1 = Channel number %2 = Block number, label Definitions: A toolholder was activated with an angle of…

Sinumerik Alarm 14150 Channel %1 block %2 illegal tool carrier number programmed or declared (MD) Parameters: %1 = Channel number %2 = Block number, label Definitions: A tool holder number…

Sinumerik Alarm 14148 Channel %1 illegal reference system for Cartesian manual traverse Parameters: %1 = Channel number Definitions: In the setting data SC_CART_JOG_MODE, an illegal value has been entered for…

Sinumerik Alarm 14146 Channel %1 block %2 CP or PTP movement without transformation not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: The CP or PTP…

Sinumerik Alarm 14144 Channel %1 block %2 PTP movement not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: The PTP G code was programmed for a…

Sinumerik Alarm 14140 Channel %1 block %2 position programming without transformation not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: Position information was programmed for an…

Sinumerik Alarm 14134 Channel %1 block %2 G code for orientation interpolation not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: It is only possible to…

Sinumerik Alarm 14133 Channel %1 block %2 G code for orientation definition not allowed Parameters: %1 = Channel number %2 = Block number, label Definitions: It is only possible to…

Sinumerik Alarm 14132 Channel %1 block %2 orientation axes incorrectly configured Parameters: %1 = Channel number %2 = Block number, label Definitions: The configuration of the orientation axes does not…

Sinumerik Alarm 14131 Channel %1 block %2 orientation axes and lead/tilt angles programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: An orientation angle and a leading…

Sinumerik Alarm 14130 Channel %1 block %2 too many initialization values given Parameters: %1 = Channel number %2 = Block number, label Definitions: On assigning an array by means of…

Sinumerik Alarm 14129 Channel %1 block %2 orientation angles and orientation vector components programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: An orientation angle and components…

Sinumerik Alarm 14125 Channel %1 block %2 programmed rotation is not possible Parameters: %1 = Channel number %2 = Block number, label Definitions: The programmed rotation of tool orientation cannot…

Sinumerik Alarm 14124 Channel %1 block %2 start tangent for orientation is zero Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation with tangential…

Sinumerik Alarm 14123 Channel %1 block %2 nutation angle of the cone too small Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation, the…

Sinumerik Alarm 14122 Channel %1 block %2 angle and direction of the cone programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation of…

Sinumerik Alarm 14120 Channel %1 block %2 plane determination for programmed orientation not possible Parameters: %1 = Channel number %2 = Block number, label Definitions: The programmed orientation vectors (direction…

Sinumerik Alarm 14119 Channel %1 block %2 no intermediate orientation programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation of orientation with ORICONIO,…

Sinumerik Alarm 14118 Channel %1 block %2 no end orientation programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation of orientation, no end…

Sinumerik Alarm 14117 Channel %1 block %2 no angle or direction of the cone programmed Parameters: %1 = Channel number %2 = Block number, label Definitions: With taper circumference interpolation…

Sinumerik Alarm 14116 Channel %1 block %2 absolute orientation programmed while ORIPATH is active Parameters: %1 = Channel number %2 = Block number, label Definitions: The orientation has been entered…

Sinumerik Alarm 14115 Channel %1 block %2 illegal definition of workpiece surface Parameters: %1 = Channel number %2 = Block number, label Definitions: The surface normal vectors programmed at the…

Sinumerik Alarm 14114 Channel %1 block %2 programmed tilt angle too large Parameters: %1 = Channel number %2 = Block number, label Definitions: No further explanation. Reactions: – Alarm display….

Sinumerik Alarm 14113 Channel %1 block %2 programmed lead angle too large Parameters: %1 = Channel number %2 = Block number, label Definitions: No further explanation. Reactions: – Alarm display….

Sinumerik Alarm 14112 Channel %1 block %2 programmed orientation path not possible Parameters: %1 = Channel number %2 = Block number, label Definitions: In 5-axis transformation, the two orientation axes…