Sinumerik Alarms

Sinumerik Alarm 111115 Programmed position was not reached Definitions: The alarms 111110, 111115, 111126, 111127 and 111200 can occur at spindle start/stop. Reactions: – Alarm display. Remedy: Inform the service…

Sinumerik Alarm 111420 Error during the inch/metric conversion! Check all data! Definitions: The switchover of the data for the inch/metric conversion was not completed. This alarm can only appear in…

Sinumerik Alarm 111302 Spindle start key defective Definitions: Acknowledgement to the PLC user program, that the spindle start key is defective, i.e., NC and NO signal = 1. Reactions: –…

Sinumerik Alarm 111904 4. Axis not configured, i.e., no driven tool possible Definitions: 4. The axis is not configured, i.e., no driven tool is possible. Reactions: – Alarm display. Remedy:…

Sinumerik Alarm 111305 Asynchronous subroutine was not executed Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of the alarms from…

Sinumerik Alarm 112045 Several insertion points required Definitions: Several insertion points are required for machining the contour pocket. The machining breaks up into several individual machinings. The program can be…

Sinumerik Alarm 111306 Error when selecting or deselecting constant cutting speed Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of…

Sinumerik Alarm 111307 Error when deleting handwheel offset Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of the alarms from…

Sinumerik Alarm 111308 Error when setting upper spindle speed limit Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of the…

Sinumerik Alarm 111309 Error when selecting tool Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of the alarms from 111306…

Sinumerik Alarm 112099 System-error contour pocket Definitions: While the contour pocket was being calculated, an error occurred. The contour pocket cannot be calculated. The program cannot be started. Reactions: –…

Sinumerik Alarm 111310 Error when selecting zero offset Definitions: In the asynchronous subroutine, internal settings in the NC were triggered by the operator panel. If one of the alarms from…

Sinumerik Alarm 112100 Error during renumbering. Original state restored. Definitions: The soft key “Renumber” was pressed in the program editor. This caused an error during serial numbering that damaged the…

Sinumerik Alarm 111311 NC start not possible: Deselect single block Definitions: A program was activated with block search, while at the same time single block was active. Reactions: – NC…

Sinumerik Alarm 112200 The contour is a step in the current program sequence. Machining not enabled Definitions: The contour is an element from a loaded program and cannot be deleted…

Sinumerik Alarm Definitions: When ManualTurn is booted, a check is run to see whether all standard tools are available. If this is not the case, the missing tools will be…

Sinumerik Alarm 111430 Program not loaded. Error when converting old cycles in G code. No NC memory. Definitions: In previous ManualTurn versions, LINE, INCLINED and CIRCLE steps were saved as…

Sinumerik Alarm Definitions: A G code program can only be started from the basic display of an operating mode (except MANUAL). Reactions: – Alarm display. Remedy: Switch to the basic…

Sinumerik Alarm Definitions: There is a contour in the current Easystep sequence and it is not permitted to be changed. Reactions: – Alarm display. Remedy: Terminate machining. Reload the Easystep…

Sinumerik Alarm Definitions: The axes have no valid reference point. Reactions: – Alarm display. Remedy: Reference all axes. Program Continuation: Internal

Sinumerik Alarm 112046 Main contour cannot be bypassed Definitions: The pocket contour cannot be bypassed with the specified milling cutter. Residual material will remain. The program can be started. This…

Sinumerik Alarm 112052 No residual material generated Definitions: No residual material was generated. It could be, that there is no more residual material to machine. The program can be started….

Sinumerik Alarm 112057 Programmed helix violates contour Definitions: The starting point for helical insertion was so selected, that the helix violates the programmed contour. The program can be started. This…

Sinumerik Alarm 111400 Unknown PLC error Definitions: The PLC has announced an error that is unknown in the operator panel. Reactions: – NC Start disable in this channel. – Alarm…

Sinumerik Alarm 111410 Tool %1 was created Parameters: %1 = Tool number Definitions: When ManualTurn is booted, a check is run to see whether all standard tools are available. If…

Sinumerik Alarm 112211 Tool preselection could not be processed. Insufficient NC memory. Definitions: When tool preselection is processed, the NC program has to be generated again. Hereby the old NC…

Sinumerik Alarm 112502 Insufficient memory, abort in line %1 Parameters: %1 = Line number Definitions: The program cannot interpret a program block with contour programming. Contour not in the directory….

Sinumerik Alarm 112300 Tool management type 2 not possible. Magazine not completely loaded. Definitions: The magazine is not completely loaded with tools. In the magazine of tool management type 2,…

Sinumerik Alarm 112301 Tool management type 2 not possible. The magazine is not sorted as in the tool list. Definitions: The magazine list sorting does not correspond to that of…

Sinumerik Alarm 112323 Replace swivel head. Definitions: The operator is prompted to remove the specified swivel head from the spindle. Reactions: – Alarm display. Remedy: Replace swivel head. When doing…

Sinumerik Alarm 112324 Load swivel head. Definitions: The operator is prompted to load the specified swivel head into the spindle. Reactions: – Alarm display. Remedy: Load swivel head. When doing…

Sinumerik Alarm 112325 Exchange swivel head. Definitions: The operator is prompted to replace the specified swivel head in the spindle with the new swivel head. Reactions: – Alarm display. Remedy:…

Sinumerik Alarm 112326 Set swivel head Definitions: The operator is prompted to set the swivel head in accordance with the specified data. Reactions: – Alarm display. Remedy: Set swivel head….

Sinumerik Alarm 112327 Angle not in permissible area Definitions: The programmed machining cannot be carried out with the swivel head. Reactions: – Alarm display. Remedy: If necessary, clamp the workpiece…

Sinumerik Alarm 112328 Angle adapted to angle grid. Definitions: Due to the angle grid, the swivel head could not be set exactly to the specified angle. Reactions: – Alarm display….