- 16000 Channel %1 block %2 invalid value for lifting direction
- 16005 Channel %1 block %2 invalid value for lifting distance
- 16010 Channel %1 block %2 machining stop after lift fast
- 16015 Channel %1 block %2 wrong axis identifier %3
- 16016 Channel %1 block %2 no retraction position programmed for axis %3
- 16020 Channel %1 repositioning in block %2 is not possible
- 16100 Channel %1 block %2 spindle %3 not available in the channel
- 16105 Channel %1 block %2 spindle %3 cannot be assigned
- 16110 Channel %1 block %2 spindle %3 for dwell time not in control mode
- 16120 Channel %1 block %2 invalid index for tool fine compensation
- 16130 Channel %1 block %2 instruction not allowed with FTOCON
- 16140 Channel %1 block %2 FTOCON not allowed
- 16150 Channel %1 block %2 invalid spindle number with PUTFTOCF
- 16200 Channel %1 block %2 spline and polynominal interpolation not available
- 16300 Channel %1 block %2 denominator polynominal with zero places within parameter range not allowed
- 16400 Channel %1 block %2 positioning axis %3 cannot participate in spline
- 16410 Channel %1 block %2 axis %3 is not a geometry axis
- 16420 Channel %1 block %2 axis %3 programmed repeatedly
- 16421 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16422 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16423 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16424 Channel %1 block %2 coordinate %3 programmed repeatedly in the block
- 16430 Channel %1 block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
- 16440 Channel %1 block %2 rotation programmed for non-existent geometry axis
- 16500 Channel %1 block %2 chamfer or rounding negative
- 16510 Channel %1 block %2 no facing axis available
- 16700 Channel %1 block %2 axis %3 invalid feed type
- 16710 Channel %1 block %2 axis %3 master spindle not programmed
- 16715 Channel %1 block %2 axis %3 spindle not in standstill
- 16720 Channel %1 block %2 axis %3 thread lead is zero
- 16730 Channel %1 block %2 axis %3 wrong parameter
- 16740 Channel %1 block %2 no geometry axis programmed
- 16750 Channel %1 block %2 axis %3 SPCON not programmed
- 16751 Channel %1 block %2 spindle/axis %3 SPCOF not executable
- 16755 Channel %1 block %2 no stop required
- 16760 Channel %1 block %2 axis %3 S value missing
- 16761 Channel %1 block %2 axis/spindle %3 not programmable in the channel
- 16762 Channel %1 block %2 spindle %3 thread function is active
- 16763 Channel %1 block %2 axis %3 programmed speed is illegal (zero or negative)
- 16770 Channel %1 block %2 axis %3 no measuring system available
- 16771 Channel %1 following axis %2 overlaid movement not enabled
- 16776 Channel %1 block %2 curve table %3 does not exist for axis %4
- 16777 Channel %1 block %2 coupling: following axis %3 for lead axis %4 not available
- 16778 Channel %1 block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible
- 16779 Channel %1 block %2 coupling: too many couplings for axis %3, see active leading axis %4
- 16780 Channel %1 block %2 following spindle/axis missing
- 16781 Channel %1 block %2 master spindle/axis missing
- 16782 Channel %1 block %2 following spindle/axis %3 not available
- 16783 Channel %1 block %2 master spindle/axis %3 not available
- 16785 Channel %1 block %2 identical spindles/axes %3
- 16787 Channel %1 block %2 coupling parameter not changeable
- 16788 Channel %1 block %2 cyclic coupling
- 16789 Channel %1 block %2 multiple link
- 16790 Channel %1 block %2 Parameter is zero or missing
- 16791 Channel %1 block %2 parameter is not relevant
- 16792 Channel %1 block %2 too many couplings for axis/spindle %3
- 16793 Channel %1 block %2 coupling of axis %3 prohibits transformation change
- 16794 Channel %1 block %2 coupling of axis/spindle %3 prohibits reference point approach
- 16795 Channel %1 block %2 string cannot be interpreted
- 16796 Channel %1 block %2 coupling not defined
- 16797 Channel %1 block %2 coupling is active
- 16798 Channel %1 block %2 axis %3 is following axis and prohibits axis container rotation
- 16799 Channel %1 block %2 axis %3 is master axis and prohibits axis container rotation
- 16800 Channel %1 block %2 traverse instruction DC/CDC for axis %3 not allowed
- 16810 Channel %1 block %2 traverse instruction ACP for axis %3 not allowed
- 16820 Channel %1 block %2 traverse instruction ACN for axis %3 not allowed
- 16830 Channel %1 block %2 incorrect position programmed for axis/spindle %3
- 16903 Channel %1 program control: action %2 not allowed in the current state
- 16904 Channel %1 program control: action %2 not allowed in the current state
- 16905 Channel %1 program control: action %2 not allowed
- 16906 Channel %1 program control: action %2 is aborted due to an alarm
- 16907 Channel %1 action %2 only possible in stop state
- 16908 Channel %1 action %2 only possible in reset state or at the block end
- 16909 Channel %1 action %2 not allowed in current mode
- 16911 Channel %1 mode change is not allowed
- 16912 Channel %1 program control: action %2 only possible in reset state
- 16913 Mode group %1 channel %2 mode change: action %3 not allowed
- 16914 Mode group %1 channel %2 mode change: action %3 not allowed
- 16915 Channel %1 action %2 not allowed in the current block
- 16916 Channel %1 repositioning: action %2 not allowed in the current state
- 16918 Channel %1 for action %2 all channels must be in reset state
- 16919 Channel %1 action %2 is not allowed due to a pending alarm
- 16920 Channel %1 action %2 is already active
- 16921 Channel %1 mode group %2 machine data: channel/mode group assignment not allowed or assigned twice
- 16922 Channel %1 subprograms: action %2 maximum nesting depth exceeded
- 16923 Channel %1 program control: action %2 not allowed in the current state
- 16924 Channel %1 caution: program test modifies tool management data
- 16925 Channel %1 program control: action %2 not allowed in the current state, action %3 active
- 16926 Channel %1 channel coordination: action %2 not allowed in block %3, marker %4 is already set
- 16927 Channel %1 action %2 at active interrupt treatment not allowed
- 16928 Channel %1 interrupt treatment: action %2 not possible
- 16930 Channel %1: preceding block and current block %2 must be separated through an executable block
- 16931 Channel %1 subprograms: action %2 maximum nesting depth exceeded
- 16932 Channel %1 conflict when activating user data type %2
- 16933 Channel %1 interrupt treatment: action %2 not allowed in the current state
- 16934 Channel %1 interrupt treatment: action %2 not possible due to stop
- 16935 Channel %1 action %2 not possible due to search run
- 16936 Channel %1 action %2 not possible due to active dry run
- 16937 Channel %1 action %2 not possible due to program test
- 16938 Channel %1 action %2 aborted due to active gear change
- 16939 Channel %1 action %2 rejected due to active gear change
- 16940 Channel %1 action %2 wait for gear change
- 16941 Channel %1 action %2 rejected because no program event has been executed yet
- 16942 Channel %1 start program command action %2 not possible
- 16943 Channel %1 action %2 not possible due to ASUP
- 16944 Channel %1 action %2 not possible due to active search blocks
- 16945 Channel %1 action %2 delayed up to the block end
- 16946 Channel %1 start via START is not allowed
- 16947 Channel %1 start via PLC is not allowed
- 16948 Channel %1 dependent channel %2 still active
- 16949 Correspondence between marker of channel %1 and channel %2 is invalid.
- 16950 Channel %1 search run with hold block
- 16951 Channel %1 search run in a program section that cannot be searched
- 17000 Channel %1 block %2 maximum number of symbols exceeded
- 17001 Channel %1 block %2 no memory left for tool/magazine data
- 17010 Channel %1 block %2 no memory left
- 17020 Channel %1 block %2 illegal array index 1
- 17030 Channel %1 block %2 illegal array index 2
- 17040 Channel %1 block %2 illegal axis index
- 17050 Channel %1 block %2 illegal value
- 17055 Channel %1 block %2 GUD variable not existing
- 17060 Channel %1 block %2 requested data area too large
- 17070 Channel %1 block %2 data is write-protected
- 17080 Channel %1 block %2 %3 value below lower limit
- 17090 Channel %1 block %2 %3 value exceeds upper limit
- 17095 Channel %1 block %2 invalid value
- 17100 Channel %1 block %2 digital input/comparator no. %3 not activated
- 17110 Channel %1 block %2 digital output no. %3 not activated
- 17120 Channel %1 block %2 analog input no. %3 not activated
- 17130 Channel %1 block %2 analog output no. %3 not activated
- 17140 Channel %1 block %2 NCK output %3 is assigned to a function via machine data
- 17150 Channel %1 block %2 maximum of %3 NCK outputs programmable in the block
- 17160 Channel %1 block %2 no tool selected
- 17170 Channel %1 block %2 number of symbols too large
- 17180 Channel %1 block %2 illegal D number
- 17181 Channel %1 block %2 T no.= %3, D no.= %4 not existing
- 17182 Channel %1 block %2 illegal sum correction number
- 17188 Channel %1 D number %2 defined in tool T no. %3 and %4
- 17189 Channel %1 D number %2 of tools defined on magazine/location %3 and %4
- 17190 Channel %1 block %2 illegal T number
- 17191 Channel %1 block %2 T= %3 not existing, program %4
- 17192 TO unit %1 invalid tool designation of ‘%2’, duplo no. %3. No more replacement tools possible in ‘%4’.
- 17193 Channel %1 block %2 the active tool is no longer on toolholder no./spindle no. %3, program %4
- 17194 Channel %1 block %2 no suitable tool found
- 17200 Channel %1 block %2 deleting tool data not possible
- 17202 Channel %1 block %2 deleting magazine data not possible
- 17210 Channel %1 block %2 access to variable not possible
- 17212 Channel %1 tool management: Load manual tool %3, duplo no. %2 onto spindle/ toolholder %4
- 17214 Channel %1 tool management: remove manual tool %3 from spindle/toolholder %2
- 17216 Channel %1 tool management: remove manual tool from spindle/toolholder %4 and load manual tool %3, duplo no. %2
- 17220 Channel %1 block %2 tool not existing
- 17230 Channel %1 block %2 Duplo no. already assigned
- 17240 Channel %1 block %2 illegal tool definition
- 17250 Channel %1 block %2 illegal magazine definition
- 17260 Channel %1 block %2 illegal magazine location definition
- 17262 Channel %1 block %2 illegal tool adapter operation
- 17270 Channel %1 block %2 call-by-reference: illegal variable
- 17500 Channel %1 block %2 axis %3 is not an indexing axis
- 17501 Channel %1 block %2 indexing axis %3 with Hirth tool system is active
- 17502 Channel %1 block %2 indexing axis %3 with Hirth tooth system stop is delayed
- 17503 Channel %1 block %2 indexing axis %3 with Hirth tooth system and axis not referenced
- 17510 Channel %1 block %2 invalid index for indexing axis %3
- 17600 Channel %1 block %2 preset on transformed axis %3 not possible
- 17605 Channel %1 block %2 axis %3 transformation active: inhibits rotation of axis container
- 17610 Channel %1 block %2 axis %3 involved in the transformation, action cannot be carried out
- 17620 Channel %1 block %2 approaching fixed point for transformed axis %3 not possible
- 17630 Channel %1 block %2 referencing for transformed axis %3 not possible
- 17640 Channel %1 block %2 spindle operation for transformed axis %3 not possible
- 17650 Channel %1 block %2 machine axis %3 not programmable
- 17800 Channel %1 block %2 illegally coded position programmed
- 17900 Channel %1 block %2 axis %3 is no machine axis
- 18000 Channel %1 block %2 NCK-specific protection zone %3 wrong. Error code %4
- 18001 Channel %1 block %2 channel-specific protection zone %3 incorrect. Error code %4
- 18002 Channel %1 block %2 NCK protection zone %3 cannot be activated. Error code %4
- 18003 Channel %1 block %2 NCK protection zone %3 cannot be activated.Error code %4
- 18004 Channel %1 block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4
- 18005 Channel %1 block %2 serious error in definition of NCK-specific protection zone %3
- 18006 Channel %1 block %2 serious error in definition of channel-specific protection zone %3
- 18100 Channel %1 block %2 invalid value assigned to FXS[]
- 18101 Channel %1 block %2 invalid value assigned to FXST[]
- 18102 Channel %1 block %2 invalid value assigned to FXSW[]
- 18200 Channel %1 block %2 curve table: block search stop not allowed with definition CTABDEF
- 18201 Channel %1 block %2 curve table: table %3 does not exist
- 18202 Channel %1 block %2 curve table: instruction CTABEND without CTABDEF not allowed
- 18300 Channel %1 block %2 frame: fine shift not possible
- 18310 Channel %1 block %2 frame: illegal rotation
- 18311 Channel %1 block %2 frame: illegal instruction
- 18312 Channel %1 block %2 frame: fine shift not configured
- 18313 Channel %1 block %2 frame: illegal switchover of geometry axes
- 18314 Channel %1 block %2 frame: type conflict
- 18400 Channel %1 block %2 language change not possible:
- 20000 Channel %1 axis %2 reference cam not reached
- 20001 Channel %1 axis %2 no cam signal present
- 20002 Channel %1 axis %2 zero mark not found
- 20003 Channel %1 axis %2 measuring system error
- 20004 Channel %1 axis %2 reference mark missing
- 20005 Channel %1 axis %2 reference point approach aborted
- 20006 Channel %1 axis %2 reference point creep velocity not reached
- 20007 Channel %1 axis %2 reference point approach requires 2 measuring systems
- 20008 Channel %1 axis %2 reference point approach requires second referenced measuring system
- 20050 Channel %1 axis %2 handwheel mode active
- 20051 Channel %1 axis %2 handwheel mode not possible
- 20052 Channel %1 axis %2 already active
- 20053 Channel %1 axis %2 DRF, FTOCON, external zero point offset not possible
- 20054 Channel %1 axis %2 wrong index for indexing axis in JOG mode
- 20055 Channel %1 master spindle not present in JOG mode
- 20056 Channel %1 axis %2 no revolutional feedrate possible. Axis/spindle %3 stationary
- 20057 Channel %1 block %2 revolutional feedrate for axis/spindle %3 is <= zero
- 20058 Channel %1 axis %2 revolutional feedrate: illegal feed source
- 20060 Channel %1 axis %2 cannot be traversed as geometry axis
- 20061 Channel %1 axis %2 cannot be traversed as orientation axis
- 20062 Channel %1 axis %2 already active
- 20063 Channel %1 axis %2 orientation axes cannot be traversed without transformation
- 20065 Channel %1 master spindle not defined for geometry axes in JOG mode
- 20070 Channel %1 axis %2 programmed end position is behind software limit switch %3
- 20071 Channel %1 axis %2 programmed end position is behind working area limit %3
- 20072 Channel %1 axis %2 is not an indexing axis
- 20073 Channel %1 axis %2 cannot be repositioned
- 20074 Channel %1 axis %2 wrong index position
- 20075 Channel %1 axis %2 can currently not oscillate
- 20076 Channel %1 axis %2 oscillating – mode change not possible
- 20077 Channel %1 axis %2 programmed position is behind software limit switch %3
- 20078 Channel %1 axis %2 programmed position is behind working area limit %3
- 20079 Channel %1 axis %2 oscillation path length %3 <= 0
- 20080 Channel %1 axis %2 no handwheel assigned for overlaid motion
- 20085 Channel %1 contour handwheel: traverse direction or overtravel of beginning of block not allowed
- 20090 Axis %1 travel to fixed stop not possible. Check programming and axis data.
- 20091 Axis %1 has not reached fixed stop
- 20092 Axis %1 travel to fixed stop still active
- 20093 Axis %1 standstill monitoring at fixed-stop end point has been triggered
- 20094 Axis %1 function has been aborted
- 20095 Axis %1 illegal torque, current torque %2
- 20096 Axis %1 brake test aborted, additional information %2
- 20100 Channel %1: invalid configuration for digitizing function
- 20101 Communication with the digitizer not possible
- 20102 Channel %1: No or invalid trafo at digitizing active
- 20103 Channel %1: digitizing module does not support 3+2 axis digitizing
- 20105 Channel %1: axes stopped by digitizer. Error code: %2
- 20106 Emergency stop set by the digitizer
- 20108 Invalid data package received from the digitizer. Error codes: %1, %2
- 20109 Error in communication with the digitizer: status code of com-circuit: %1
- 20120 Axis %1: too many compensation relations
- 20121 Axis %1: Configuration error in compensation table %2
- 20122 Compensation table %1: invalid axis assignment
- 20123 Axis %1: different output assignment of multiplied tables
- 20124 Axis %1: sum of compensation values too large
- 20125 Axis %1: change of compensation value is too rapid
- 20130 Channel %1 contour tunnel monitoring
- 20140 Channel %1 motion synchronous action: traversing of command axis %2 see NC alarm %3
- 20141 Channel %1 motion synchronous action: illegal axis type
- 20142 Channel %1 command axis %2: rotation of axis container already enabled
- 20143 Channel %1 axis %2 command axis cannot be started as it is controlled by the PLC
- 20144 Channel %1 block %2 motion synchronous action: system variable access not possible
- 20145 Channel %1 block %2 motion synchronous action: arithmetic error
- 20146 Channel %1 block %2 motion synchronous action: nesting depth exceeded
- 20147 Channel %1 block %2 motion synchronous action: command not executable
- 20148 Channel %1 block %2 motion synchronous action: internal error %3
- 20149 Channel %1 block %2 motion synchronous action: illegal index
- 20150 Channel %1 tool management: PLC terminates interrupted command
- 20160 Channel %1 tool management: PLC can terminate only incorrectly aborted commands
- 20170 Channel %1 machine data $AC_FIFO invalid
- 20200 Channel %1 invalid spindle number %2 with tool fine compensation
- 20201 Channel %1 spindle %2 no tool assigned
- 20203 Channel %1 no active tool
- 20204 Channel %1 PUTFTOC command not allowed with FTOCOF
- 20210 Channel %1 block %3 spindle %2 wrong values for centerless grinding
- 20211 Channel %1 block %3 spindle %2 support point beyond range limits
- 21600 Monitoring for ESR active
- 21610 Channel %1 axis %2 encoder %3 frequency limit exceeded
- 21611 Channel %1 NC-controlled Extended Stop/Retract triggered
- 21612 Channel %1 axis %2 VDI signal ‘Servo enable’ reset during motion
- 21613 Axis %1 measuring system changing
- 21614 Channel %1 axis %2 hardware limit switch %3
- 21615 Channel %1 axis %2 taken from traverse mode to follow-up mode
- 21616 Channel %1 block %2 overlaid motion active at transformation switchover
- 21617 Channel %1 block %2 transformation does not allow to traverse the pole
- 21618 Channel %1 as from block %2 transformation active: overlaid motion too great
- 21619 Channel %1 block %2 transformation active: motion not possible
- 21650 Channel %1 axis %2 overlaid motion not allowed
- 21660 Channel %1 block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF
- 21665 Channel %1 $AA_TOFF cleared
- 21670 Channel %1 block %2 illegal change of tool direction with $AA_TOFF active
- 21700 Channel %1 block %3 axis %2 touch probe already deflected, edge polarity not possible
- 21701 Channel %1 block %3 axis %2 measurement not possible
- 21702 Channel %1 block %3 axis %2 measurement aborted
- 21703 Channel %1 block %3 axis %2 touch probe not deflected, illegal edge polarity
- 21740 Output value at analog output no. %1 has been limited
- 21750 Error during output of cam signals via timer
- 21760 Channel %1 block %2 too many auxiliary functions programmed
- 21800 Channel %1 workpiece setpoint %2 reached
- 22000 Channel %1 block %3 spindle %2 change of gear stage not possible
- 22010 Channel %1 block %3 spindle %2 actual gear stage differs from requested gear stage
- 22011 Channel %1 block %3 spindle %2 change to programmed gear stage not possible
- 22012 Channel %1 block %2 leading spindle %3 is in simulation.
- 22013 Channel %1 block %2 dependent spindle %3 is in simulation.
- 22014 Channel %1 block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably
- 22020 Channel %1 block %3 spindle %2 gear step change position not reached
- 22040 Channel %1 block %3 spindle %2 is not referenced with zero marker
- 22045 Block %2 spindle/axis %3 not available in channel %1 because active in channel %4
- 22050 Channel %1 block %3 spindle %2 no transition from speed control mode to position control mode
- 22051 Channel %1 block %3 spindle %2 reference mark not found
- 22052 Channel %1 block %3 spindle %2 no standstill on block change
- 22053 Channel %1 block %3 spindle %2 reference mode not supported
- 22054 Channel %1 block %3 spindle %2 improper punching signal
- 22055 Channel %1 block %3 spindle %2 configured positioning speed is too high
- 22060 Channel %1 position control expected for axis/spindle %2
- 22062 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached
- 22064 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high
- 22065 Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
- 22066 Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
- 22067 Channel %1 tool management: tool change not possible since there is no tool available in tool group %2
- 22068 Channel %1 block %2 tool management: no tool available in tool group %3
- 22069 Channel %1 block %2 tool management: No tool available in tool group %3, program %4
- 22070 TO unit %1 Please change tool T= %2 into magazine. Repeat data backup
- 22071 TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration
- 22100 Channel %1 block %3 spindle %2 chuck speed exceeded
- 22200 Channel %1 spindle %2 axis stopped during tapping
- 22250 Channel %1 spindle %2 axis stopped during thread cutting
- 22260 Channel %1 spindle %2 thread might be damaged
- 22270 Channel %1 block %2 maximum velocity of thread axis at position %3 reached
- 22275 Channel %1 block %2 zero velocity of thread axis at position %3 reached
- 22280 Channel %1 in block %2: Prog. acceleration path too short %3, %4 required
- 22320 Channel %1 block %2 PUTFTOCF command could not be transferred
- 22321 Channel %1 axis %2 PRESET not allowed during traverse motion
- 22322 Channel %1 axis %2 PRESET: illegal value
- 25000 Axis %1 hardware fault of active encoder
- 25001 Axis %1 hardware fault of passive encoder
- 25010 Axis %1 pollution of measuring system
- 25011 Axis %1 pollution of passive encoder
- 25020 Axis %1 zero mark monitoring of active encoder
- 25021 Axis %1 zero mark monitoring of passive encoder
- 25022 Axis %1 encoder %2 warning %3
- 25030 Axis %1 actual velocity alarm limit
- 25031 Axis %1 actual velocity warning limit
- 25040 Axis %1 standstill monitoring
- 25042 Axis %1 standstill monitoring during torque/force limitation
- 25050 Axis %1 contour monitoring
- 25060 Axis %1 speed setpoint limitation
- 25070 Axis %1 drift value too large
- 25080 Axis %1 positioning monitoring
- 25100 Axis %1 measuring system switchover not possible
- 25105 Axis %1 measuring systems differ considerably
- 25110 Axis %1 selected encoder not available
- 25200 Axis %1 requested set of parameters invalid
- 25201 Axis %1 drive fault
- 25202 Axis %1 waiting for drive
- 26000 Axis %1 clamping monitoring
- 26001 Axis %1 parameterization error: friction compensation
- 26002 Axis %1 encoder %2 parameterization error: number of encoder marks
- 26003 Axis %1 parameterization error: lead screw pitch
- 26004 Axis %1 encoder %2 parameterization error: grid point distance with linear encoders
- 26005 Axis %1 parameterization error: output rating
- 26006 Axis %1 encoder %2 encoder type/output type %3 not possible
- 26007 Axis %1 QEC: invalid coarse step size
- 26008 Axis %1 QEC: invalid fine step size
- 26009 Axis %1 QEC: memory overflow
- 26010 Axis %1 QEC: invalid acceleration characteristic
- 26011 Axis %1 QEC: invalid measuring periods
- 26012 Axis %1 QEC: feed forward control not active
- 26014 Axis %1 machine data %2 invalid value
- 26015 Axis %1 machine data %2[%3] invalid value
- 26016 Axis %1 machine data %2 invalid value
- 26017 Axis %1 machine data %2[%3] invalid value
- 26018 Axis %1 setpoint output drive %2 used more than once
- 26019 Axis %1 encoder %2 measurement not possible with this controller module
- 26020 Axis %1 encoder %2 hardware fault %3 during encoder initialization
- 26022 Axis %1 encoder %2 measurement with simulated encoder not possible
- 26024 Axis %1 machine data %2 value changed
- 26025 Axis %1 machine data %2[%3] value changed
- 26030 Axis %1 encoder %2 absolute position lost
- 26031 Axis %1 configuration error master-slave
- 26032 Axis %1 master-slave not configured
- 26050 Axis %1 parameter set change from %2 to %3 not possible
- 26051 Channel %1 in block %2 unanticipated stop crossed in continuous path mode
- 26052 Channel %1 in block %2: path velocity too high for auxiliary function output
- 26070 Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded
- 26072 Channel %1 axis %2 cannot be controlled by the PLC
- 26074 Channel %1 switching off PLC control of axis %2 not allowed in the current state
- 26080 Channel %1 retraction position of axis %2 not programmed or invalid
- 26081 Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled
- 26100 Axis %1 drive %2 sign of life missing
- 26101 Axis %1 drive %2 communication failure
- 26102 Axis %1 drive %2 sign of life missing
- 26105 Drive of axis %1 not found
- 26106 Encoder %2 of axis %1 not found
- 26110 Independent drive stop/retract triggered
- 27000 Axis %1 is not safely referenced
- 27001 Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4
- 27002 Axis %1 test stop is running
- 27003 Checksum error found: %1 %2
- 27004 Axis %1, difference safe input %2, NCK %3, drive %4
- 27005 Axis %1 error in data cross check: static actual value difference
- 27006 Axis %1 Test ext. pulse deletion running
- 27007 Axis %1 acceptance test mode is active
- 27008 Axis %1 SW limit switch deactivated
- 27010 Axis %1 tolerance for safe standstill exceeded
- 27011 Axis %1 safe velocity exceeded
- 27012 Axis %1 safe end position exceeded
- 27013 Axis %1 safe braking ramp exceeded
- 27020 Axis %1 stop E triggered
- 27021 Axis %1 stop D triggered
- 27022 Axis %1 stop C triggered
- 27023 Axis %1 stop B triggered
- 27024 Axis %1 stop A triggered
- 27030 Axis %1 function not supported on this 611D module
- 27031 Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4)
- 27032 Axis %1 checksum error of safe monitoring. Confirmation and re-test required!
- 27033 Axis %1 parameterization of MD %2[%3] invalid
- 27034 Parameterization of MD %1 invalid
- 27090 Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4 ALSI
- 27091 Error in data cross check NCK PLC, stop of %1
- 27092 Communication broken off during NCK PLC data cross check, error detected by %1
- 27093 Checksum error NCK-SPL, %1, %2, %3
- 27094 Write access to system variable %1 only allowed from NCK-SPL
- 27095 %1 SPL protection not activated
- 27096 SPL start not allowed
- 27100 At least one axis is not safely referenced
- 27101 Axis %1 difference in function safe operational stop, NCK: %2 drive: %3
- 27102 Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4
- 27103 Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4
- 27104 Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4
- 27105 Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4
- 27106 Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3
- 27107 Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3
- 27124 Stop A triggered at least in 1 axis
- 27200 PROFIsafe: cycle time %1 [ms] too long
- 27201 PROFIsafe: MD %1[%2]: bus segment %3 error
- 27202 PROFIsafe: MD %1[%2]: address %3 error
- 27203 PROFIsafe: MD %1[%2]: SPL assignment error
- 27204 PROFIsafe: double assignment MD %1[%2] – MD %3[%4]
- 27220 PROFIsafe: Number of NCK F modules (%1) <> number of DP modules (%2)
- 27221 PROFIsafe: NCK F module MD %1[%2] unknown
- 27222 PROFI safe: S7 F module PROFI safe address %1 unknown
- 27223 PROFIsafe: NCK F module MD %1[%2] is not a %3 module
- 27224 PROFIsafe: F module MD %1[%2] – MD %3[%4]: double assignment of PROFIsafe address
- 27225 PROFIsafe: slave %1, configuration error %2
- 27240 PROFIsafe: DP M not running up, DP info: %1
- 27241 PROFIsafe: DP M version different, NCK: %1, PLC: %2
- 27242 PROFIsafe: F module %1, %2 faulty
- 27250 PROFIsafe: configuration in DP M changed; error code %1 – %2
- 27251 PROFIsafe: F module %1, %2 reports error %3
- 27252 PROFIsafe: Slave %1, sign-of-life error
- 27253 PROFIsafe: communication fault F master component %1, error %2
- 27254 PROFIsafe: F module %1, error on channel %2; %3
- 27255 PROFIsafe: F module %1, general error
- 27256 PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time
- 27299 PROFIsafe: Diagnosis %1 %2 %3 %4
- 28000 NCU link connection to all other NCUs of the link network has been aborted
- 28001 NCU link connection to the NCU %1 of the link network has been aborted
- 28002 Error on activation of machine data, NCU network-wide machine data were modified by NCU %1
- 28004 NCU link: NCU %1 of the link network is not on the bus
- 28005 NCU link: NCU %1 of the link network not running synchronously
- 28007 NCU link: conflict in configuration data of NCU %1
- 28008 NCU link: conflict in timer setting of NCU %1
- 28009 NCU link: conflict in bus parameters of NCU %1
- 28010 NCU link: the NCU %1 has not received a message
- 28011 IPO time insufficient for NCU link. Link cycle time: %1
- 28012 NCU link: synchronization cycle signal failure %1 times
- 28020 NCU link: too many link axes configured %1
- 28030 Serious alarm on NCU %1, axes in follow-up mode
- 28031 Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode
- 28032 Emergency stop activated on NCU %1, axes in follow-up mode
- 28033 Emergency stop on NCU % 1, axes still in follow-up mode
- 29033 Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed
- 60000 Channel %1 block %2:
- 61000 Channel %1 block %2 no tool compensation active
- 61001 Channel %1 block %2 thread lead incorrect
- 61002 Channel %1 block %2 machining type wrongly defined
- 61003 Channel %1 block %2 no feed programmed in the cycle
- 61004 Channel %1 block %2 configuration geometry axis incorrect
- 61005 Channel %1 block %2 3rd geometry axis not present
- 61006 Channel %1 block %2 tool radius too large
- 61007 Channel %1 block %2 tool radius too small
- 61009 Channel %1 block %2 active tool number = 0
- 61010 Channel %1 block %2 finishing allowance too large
- 61011 Channel %1 block %2 scaling not allowed
- 61012 Channel %1 block %2 different scaling on the plane
- 61013 Channel %1 block %2 basic settings were changed, program cannot be executed
- 61101 Channel %1 block %2 reference plane incorrectly defined
- 61102 Channel %1 block %2 no spindle direction programmed
- 61103 Channel %1 block %2 number of drillings is zero
- 61104 Channel %1 block %2 contour violation of slots/long holes
- 61105 Channel %1 block %2 cutter radius too large
- 61106 Channel %1 block %2 number or distance of circular elements
- 61107 Channel %1 block %2 first drilling depth incorrectly defined
- 61108 Channel %1 block %2 illegal values for parameters _RAD1 and _DP1
- 61109 Channel %1 block %2 parameter _CDIR incorrectly defined
- 61110 Channel %1 block %2 finishing allowance at the base > depth infeed
- 61111 Channel %1 block %2 infeed width > tool diameter
- 61112 Channel %1 block %2 tool radius negative
- 61113 Channel %1 block %2 parameter _CRAD for corner radius too large
- 61114 Channel %1 block %2 machining direction G41/G42 incorrectly defined
- 61115 Channel %1 block %2 approach or retract mode (straight line/circle/plane/space) incorrectly defined
- 61116 Channel %1 block %2 approach or retraction path = 0
- 61117 Channel %1 block %2 active tool radius <= 0
- 61118 Channel %1 block %2 length or width = 0
- 61119 Channel %1 block %2 nominal or core diameter incorrectly programmed
- 61120 Channel %1 block %2 internal/external thread type not defined
- 61121 Channel %1 block %2 number of teeth per cutting edge missing
- 61122 Channel %1 block %2 safety clearance on the plane incorrectly defined
- 61124 Channel %1 block %2 infeed width is not programmed
- 61125 Channel %1 block %2 technology selection in parameter _TECHNO incorrectly defined
- 61126 Channel %1 block %2 thread length too short
- 61127 Channel %1 block %2 transmission ratio of tapping axis incorrectly defined (machine data)
- 61128 Channel %1 block %2 dipping angle = 0 for dipping with oscillation or helix
- 61180 Channel %1 block %2 no name assigned to swivel data block, although MD $MN_MM_NUM_TOOL_CARRIER > 1
- 61181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
- 61182 Channel %1 block %2 name of swivel data block unknown
- 61183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0… 2
- 61184 Channel %1 block %2 no solution possible with current input angle values
- 61185 Channel %1 block %2 no or incorrect (min > max) rotary axis angle ranges assigned
- 61186 Channel %1 block %2 rotary axis vectors invalid –> Check installation and start-up of the swivel cycle CYCLE800
- 61188 Channel %1 block %2 no axis name for the 1st axis assigned -> Check installation and start-up of the swivel cycle CYCLE800
- 61200 Channel %1 block %2 too many elements in the machining block
- 61201 Channel %1 block %2 wrong sequence in the machining block
- 61202 Channel %1 block %2 no technology cycle
- 61203 Channel %1 block %2 no positioning cycle
- 61204 Channel %1 block %2 unknown technology cycle
- 61205 Channel %1 block %2 unknown positioning cycle
- 61210 Channel %1 block %2 block search element not found
- 61211 Channel %1 block %2 absolute reference missing
- 61212 Channel %1 block %2 wrong tool type
- 61213 Channel %1 block %2 circle radius too small
- 61214 Channel %1 block %2 no lead programmed
- 61215 Channel %1 block %2 raw dimension incorrectly programmed
- 61216 Channel %1 block %2 feed/tooth only possible with milling tools
- 61217 Channel %1 block %2 cutting speed for tool radius 0 programmed
- 61218 Channel %1 block %2 feed/tooth programmed, but number of teeth is zero
- 61222 Channel %1 block %2 plane infeed greater than the tool diameter
- 61223 Channel %1 block %2 approach path too short
- 61224 Channel %1 block %2 retract path too short
- 61225 Channel %1 block %2 swivel data block unknown
- 61226 Channel %1 block %2 swivel head cannot be exchanged
- 61230 Channel %1 block %2 tool probe diameter too small
- 61231 Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill
- 61232 Channel %1 block %2 loading of magazine tool not possible
- 61233 Channel %1 block %2: Thread inclination incorrectly defined
- 61234 Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill
- 61235 Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn.
- 61236 Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn.
- 61237 Channel %1 block %2: Retraction direction unknown. Manually retract tool!
- 61238 Channel %1 block %2: Machining direction unknown.
- 61239 Channel %1 block %2: Tool change point lies in the retraction area!
- 61240 Channel %1 block %2: Wrong feed type
- 61241 Channel %1 block %2: No retraction plane defined for this machining direction.
- 61242 Channel %1 block %2: Wrong machining direction
- 61243 Channel %1 block %2: Correct tool change point, tool tip is in retraction area!
- 61244 Channel %1 block %2: Thread lead change results in an undefined thread
- 61246 Channel %1 block %2: Safety clearance too small
- 61247 Channel %1 block %2: Blank radius too small
- 61248 Channel %1 block %2: Infeed too small
- 61249 Channel %1 block %2: Number of edges too small
- 61250 Channel %1 block %2: Key width/Edge length too small
- 61251 Channel %1 block %2: Key width/Edge length too large
- 61252 Channel %1 block %2: Chamfer/Radius too large
- 61253 Channel %1 block %2: No finishing allowance programmed
- 61254 Channel %1 block %2: Error when traversing to fixed stop
- 61255 Channel %1 block %2: Cut-off error: Tool breakage?
- 61301 Channel %1 block %2 measuring probe does not switch
- 61302 Channel %1 block %2 measuring probe collision
- 61303 Channel %1 block %2 safe area exceeded
- 61308 Channel %1 block %2 check measuring distance 2a
- 61309 Channel %1 block %2 check measuring probe type
- 61310 Channel %1 block %2 scale factor is active
- 61311 Channel %1 block %2 no D number is active
- 61316 Channel %1 block %2 center point and radius cannot be determined.
- 61332 Channel %1 block %2 change tool tip position
- 61338 Channel %1 block %2 positioning velocity is zero
- 61601 Channel %1 block %2 finished-part diameter too small
- 61602 Channel %1 block %2 tool width incorrectly defined
- 61603 Channel %1 block %2 groove form incorrectly defined
- 61604 Channel %1 block %2 active tool violates programmed contour
- 61605 Channel %1 block %2 contour incorrectly programmed
- 61606 Channel %1 block %2 contour processing error
- 61607 Channel %1 block %2 starting point incorrectly programmed
- 61608 Channel %1 block %2 wrong cutting edge position programmed
- 61609 Channel %1 block %2 form incorrectly defined
- 61610 Channel %1 block %2 no infeed depth programmed
- 61611 Channel %1 block %2 no intersection point found
- 61612 Channel %1 block %2 thread axis cutting not possible
- 61613 Channel %1 block %2 undercut position incorrectly defined
- 61800 Channel %1 block %2: External CNC system missing
- 61801 Channel %1 block %2: Wrong G code selected
- 61802 Channel %1 block %2: Wrong axis type
- 61803 Channel %1 block %2 programmed axis not present
- 61804 Channel %1 block %2: Progr. position exceeds reference point
- 61805 Channel %1 block %2: The value is absolutely and incrementally programmed
- 61806 Channel %1 block %2: Incorrect axis assignment
- 61807 Channel %1 block %2 wrong spindle direction programmed (active)
- 61808 Channel %1 block %2: The final drilling depth or individual drilling depth is missing
- 61809 Channel %1 block %2: Impermissible drilling position
- 61810 Channel %1 block %2: ISO-G code not possible
- 61811 Channel %1 block %2: Impermissible ISO axis name
- 61812 Channel %1 block %2: Value(s) in the external cycle call incorrectly defined
- 61813 Channel %1 block %2: GUD value incorrectly defined
- 61814 Channel %1 block %2: Polar coordinates not possible with cycle
- 61815 Channel %1 block %2: G40 not active
- 61816 Channel %1 block %2: axes are not at the reference point
- 61817 Channel %1 block %2: The axis coordinates are within the protection zone
- 61818 Channel %1 block %2: The axis area limit values are identical
- 62000 Channel %1 block %2:
- 62100 Channel %1 block %2 no drilling cycle active
- 62101 Channel %1 block %2: Incorrect cutting direction – G3 is generated
- 62103 Channel %1 block %2: The finishing allowance is not programmed
- 62105 Channel %1 block %2 number of columns or lines is zero
- 62180 Channel %1 block %2 no name assigned to swivel data block although machine data $MN_MM_NUM_TOOL_CARRIER > 1
- 62181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
- 62182 Channel %1 block %2: Load swivel head
- 62183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0…2
- 62184 Channel %1 block %2 no solution possible with current input angle values
- 62185 Channel %1 block %2 no end stop assigned to rotary axes
- 62186 Channel %1 block %2 illegal rotary axis vectors
- 62187 Channel %1 block %2 name of swivel data block unknown
- 62200 Channel %1 block %2: Start spindle
- 63000 Channel %1 block %2:
- 65000 Channel %1 block %2:
- 66000 Channel %1 block %2:
- 67000 Channel %1 block %2:
- 68000 Channel %1 block %2:
- 70000 Compile cycle alarm
- 75000 OEM alarm
- 75005 Channel %1 block %2 CLC: General programming error
- 75010 Channel %1 block %2 CLC_LIM value exceeds MD limit
- 75015 Channel %1 block %2 CLC(0) with active TOC
- 75016 Channel %1 block %2 CLC: orientation changed for TRAFOOF
- 75020 Channel %1 CLC position offset at lower limit %2
- 75021 Channel %1 CLC position offset at upper limit %2
- 75025 Channel %1 CLC stopped because sensor head has been touched
- 75050 Channel %1 wrong MD configuration, error code %2
- 75051 Channel %1 CC_COPON CC_COPOFF error code %2
- 75060 Channel %1 tolerance window exceeded axis %2
- 75061 Channel %1 coupling active axis %2
- 75062 Channel %1 axes not in standstill axis %2
- 75070 Channel %1 wrong machine data for collision protection %2
- 75071 Channel %1 collision monitoring axis %2
- 75100 Too many analog axes configured
- 75110 Axis %1 reached drift limit
- 75200 Channel %1 wrong MD configuration, %2 incorrect
- 75210 Channel %1 number of axes/axis assignment inconsistent
- 75250 Channel %1 tool parameters incorrect
- 75255 Channel %1 working area error
- 75260 Channel %1 block %2 tool parameters incorrect
- 75265 Channel %1 block %2 working area error
- 75270 Channel %1 tool parameters incorrect
- 75275 Channel %1 block %2 working area error
- 75451 Error with definition of setpoint switchover
- 75452 Axis %1 setpoint switchover not possible in the current state
- 75500 Channel %1 wrong configuration
- 75600 Channel %1 retrace support: wrong MD configuration. Error code %2
- 75601 Channel %1 block %2 invalid parameter in CC_PREPRE()
- 75605 Channel %1 retrace support: internal error, error code %2
- 75606 Channel %1 retraceable contour was shortened
- 75607 Channel %1 resynchronisation not possible
Sinumerik 840D Alarm List – Siemens Diagnostics Guide
More ...
Sinumerik 840D CNC Programming
When I started learning cnc programming Fanuc G76 threading cycle was the most awkward cnc cycle (in my opinion) that was not easy to remember due to its too many parameters (But…
Sinumerik 840D System Variables Naming Tips
There are multiple system variables in sinumerik 840D cnc control, so remembering them is not easy. The sinumerik 840D system variables are named in a way that makes remembering them…
Siemens Sinumerik 840D Thread Cutting Cycle CYCLE97
With Sinumerik 840D Thread Cutting Cycle CYCLE97 cylindrical and tapered outside and inside threads with constant pitch in longitudinal or face machining can be machined. The thread can be single or multiple. With…
NUM CNC control Errors List – NUM 1020/1040/1060
Complete Error codes listing for NUM CNC controls NUM 1000/1020/1040/1050/1060 T and G ContentsNUM CNC control ErrorsMiscellaneous Errors and Machine ErrorsParametric Programming ErrorsProfile Geometry Programming (PGP) ErrorsMiscellaneous ErrorsAxis Overtravel ErrorsStructured Programming…
SINUMERIK 840D Programming WHILE Loop Usage
This blog post is about sinumerik 840D cnc control from Siemens. This post illustrates one of the loop commands (control structures), which we can use in cnc programming for sinumerik…
GSK CNC Alarm list – GSK980TD / GSK980TDb / GSK980TDc
GSK 980 TD / GSK 980 TDb / GSK 980 TDc alarm list for cnc machinists programmers who work on cnc lathe machines with GSK 980td / 980tdb / 980tdc…
Sinumerik 840D System Variable $P_SEARCH for Block Search Inquery
Sinumerik 840D have system variables which allow us to update and inquire different positions and behaviors of the cnc machine. No doubt sinumerik 840D is an advanced cnc control, and it gives…
Hust CNC G Code List – CNC Mill H4M & H4CL-M
Hust CNC G code list for cnc machinists who work on CNC Mill with Hust CNC controls. Following G code works on, Hust CNC H4M, Hust cnc H4CL-M and related Hust…
Sinumerik 840D System Variable $AA_IM for Axis Current Position
Siemens Sinumerik 840D gives cnc machinist the utmost flexibility to program the CNC machine the way he likes. You can create your own variables. You can access the Sinumerik 840D system…
Fadal PLC Alarms List / PLC Messages – FANUC 0i MC
Fadal PLC Alarms List / PLC Messages for Fadal Machining Centers (GE FANUC 0i MC CNC Controls). ContentsPLC AlarmsPLC Messages PLC Alarms ALARM DESCRIPTION 1002 DUAL DOOR SWITCH FAILURE 1003…
Hust CNC Lathe Controller G Code List H4CL-T & H6C-T
Complete G-Code list for Hust Lathe CNC Controllers. A good reference for CNC machinists who work on CNC Lathe with Hust CNC controls. Following G code list works on following…
SINUMERIK Operate – User Guide
All of the important functions and features of SINUMERIK Operate are briefly summarized in this SINUMERIK Operate – User Guide. SINUMERIK Operate chapter – with general operating tips – the other chapters give…
Siemens Sinumerik 808D Milling G Codes – ISO Dialect Programming
Complete list of Siemens Sinumerik 808D G Codes for CNC Machinists/CNC Programmers who work in ISO dialect mode. CNC machinists might like Siemens Sinumerik 808D Manuals Free Download SINUMERIK 808D…
Mazak G Code List (M Series)
Mazak G code list for cnc machinists who work on MAZAK machining centers. Mazak G Code List G Code Function G00 Positioning G01 Linear interpolation G01.1 Threading with C-axis interpolation…
Anilam G Code List – CNC Mill 6000M
ANILAM G Code List for CNC Mill Controls like 6000M G-codes initiate motion commands, canned cycles and various machine and CNC functions. More than one G-code may be specified per…
CNC Operating Modes
Every CNC machine has couple of Modes or I call it Standard Working Modes , such as Auto Mode, Single Block Mode, MDI (Manual Data Input) and Jog Mode and…
CYCLE81 Drilling Cycle – Sinumerik 840D Turning
Sinumerik CYCLE81 Drilling, Centering cycle for CNC machinists who work on CNC lathe/turning machine with Siemens Sinumerik CNC control. Drilling cycle CYCLE81 works on Sinumerik 840D, Sinumerik 808D and similar…
CNC Reference Point Return
What is CNC Machine Reference Point? You are operating a cnc machine sometimes in auto mode and other times in jog mode. But all the time the values which a cnc operator…
Mazak PLC Alarm List
Mazak plc alarm list for cnc machinists. Alarm List for the Mazak INTEGREX 300/400-II For other Mazak alarm lists visit following pages. Mazak System/Drive error ( No. 1 – No. 99,…
Fanuc G-Code List
CNC machines work by following the commands or instructions (G-codes / M-codes) which are given in Part Program. Here are G-codes for Fanuc cnc control which are necessary for a…