101202 SI data is copied from axis %1 to drive %2 Parameters: %1 = Axis name %2 = Drive number
101203 SI data not completely copied
101204 SI data not confirmed
101205 Drive data changed? -> Don’t forget to save the boot files!
101206 Search action running, pleas wait
101207 Position at $MN_
101208 SI data confirmed: Axis 1
101209 SI data confirmed: Drive 1
101210 The machine data is being prepared for display
101211 NCK address not changed!
101212 NCK address changed!
101213 Invalid NCK address.
101214 Initialization of this window failed!
101300 Please wait – language is being changed
103000 There is no correction block on the NCK
103001 Selection is only possible after being enabled or in the RESET state.
103002 Copying to the clipboard is not possible
103003 MDI clipboard cannot be deleted
103004 Block search not possible
103006 Block search without calculation only possible on the main program level.
103007 Ending overstore is not possible in this channel state.
103008 Block search in channel %1 started – please wait
103009 Conflict between search type and search target!
103010 Invalid file name
103011 No program selected – block search finished
103014 Please reference the axis first
104000 Current tool not found
104001 No other tools available
104002 No other cutting edges available
104003 There aren’t any tools at all
104004 No tool selected
104005 No cutting edge selected
104006 No TO area available in the current channel
104007 Error during tool creation
104008 Error during cutting edge creation
104011 Error during tool deletion
104012 No master spindle available
104014 Incorrect entry
104015 Number of parameters per cutting edge is zero
104016 No spindle available
104018 Tool not available
104019 Tool type not available
104020 No empty location found
104023 Error during tool loading
104024 Error during tool unloading
104025 No magazine configured
104026 Notice: Tool is being loaded!
104027 Notice: Tool is being unloaded!
104029 Loading to this location not possible
104030 No more data available
105000 Error x y
105001 Cycle description sc.com not available
105002 File xxx already exists
105003 Workpiece xxx already exists
105004 Clipboard empty! To PASTE, COPY first
105005 Only workpieces can be inserted here
105006 Only files can be inserted here
105007 No name specified
105008 Memory error while writing a cycle call
105009 No write-authorization for the data
105010 No data selected
105011 Cycle description cov.com not available
105012 The program is not or only partially editable (NC reset)
105013 The copied data can be inserted with the soft key “Paste”
105014 Error while copying!
105015 Error while renaming!
105016 Error while deleting!
105017 Selection is only possible after being enabled or in the RESET state.
105018 Error during program generation!
105019 Error while opening a window!
105020 Error while closing a window!
105021 Error during workpiece generation!
105022 Error during enabling!
105023 File exists already!
105024 Check values! – At least 1 value lies outside the input limits!
105025 Please wait, the directory is being prepared!
105026 Notice! The simulated program and edited program are not the same!
105030 Please wait, renumbering is being carried out!
105031 Renumbering was aborted!
105032 Renumbering finished!
105041 Block number is too large!
105042 Impermissible block number!
105043 Impermissible increment!
105050 Please wait: Graphic is being output!
105051 Output of dynamic long texts for cycle parameterization
105052 Error in the cycle description of the !
105053 No cycle available in current line!
105054 Error during cycle description call!
105060 Please wait: Initilization of the cycle support
105061 Error when opening the file!
105062 Error when closing the file!
105063 Error when positioning in the file %1!
105064 Error when reading the file!
105070 Please wait: Initialization of the simulation started!
105075 Not enough axes in the current channel? > Contour with default axis names: X, Z !
109001 No switchover: Switchover disable set in current PLC
109002 No switchover: Target PLC occupied, try again
109003 No switchover: Switchover disable set in target PLC
109004 No switchover: PLC occupied by higher-priority MMC’s
109005 No switchover: No displaceable MMC at the target PLC
109006 No switchover: Selected channel invalid
109007 Channel switchover running
109008 Activation is running
111001 Non-interpretable step in line %1
111002 Insufficient memory, abort in line %1
111003 ManualTurn: %1
111004 File faulty or not available: %1
111005 Error when interpreting the contour %1 Parameters: %1 = Contour name
111006 Maximum number of contour elements exceeded %1
111007 Error in line %1 %2
111008 Spindle not synchronized
111009 Load new tool: T%1 Parameters: %1 = Tool number
111010 Teach-in interruption: Log overflow
111100 Wrong position programmed for the spindle
111105 No measuring system available
111106 No spindle stop for a block change
111107 Reference mark not found
111108 No transition from speed control mode to position control mode
111109 Configured positioning velocity is too high
111110 Velocity/Speed is negative
111111 Setpoint speed is zero
111112 Invalid gear stage
111115 Programmed position was not reached
111126 Absolute value minus not possible
111127 Absolute value plus not possible
111200 Spindle positioning error
111300 NC start key defective
111301 NC stop key defective
111302 Spindle start key defective
111303 Spindle stop key defective
111304 Connection to the PLC broken off
111305 Asynchronous subroutine was not executed
111306 Error when selecting or deselecting constant cutting speed
111307 Error when deleting handwheel offset
111308 Error when setting upper spindle speed limit
111309 Error when selecting tool
111310 Error when selecting zero offset
111311 NC start not possible: Deselect single block
111400 Unknown PLC error
111410 Tool %1 was created
111411 %1 Tool(s) can (could) not be created
111420 Error during the inch/metric conversion! Check all data!
111430 Program not loaded. Error when converting old cycles in G code. No NC memory.
111900 Start only possible in basic display
111901 Contour is contained in the current program, machining not enabled
111902 Start only with valid reference point
111904 4. Axis not configured, i.e., no driven tool possible
112045 Several insertion points required
112046 Main contour cannot be bypassed
112052 No residual material generated
112057 Programmed helix violates contour
112099 System-error contour pocket
112100 Error during renumbering. Original state restored.
112200 The contour is a step in the current program sequence. Machining not enabled
112201 The contour is a step in the current automatic sequence. Machining not enabled
112210 Tool axis cannot be switched over. Insufficient NC memory.
112211 Tool preselection could not be processed. Insufficient NC memory.
112300 Tool management type 2 not possible. Magazine not completely loaded.
112301 Tool management type 2 not possible. The magazine is not sorted as in the tool list.
112323 Replace swivel head.
112324 Load swivel head.
112325 Exchange swivel head.
112326 Set swivel head
112327 Angle not in permissible area
112328 Angle adapted to angle grid.
112329 Set swivel head/table
112330 Set swivel table.
112350 No swivel data set up.
112360 The step was not accepted into the program sequence, as the program is running.
112400 Is not available in the tool management
112401 Tool could not be created
112420 Error during the inch/metric conversion! Check all data!
112502 Insufficient memory, abort in line %1
112504 File faulty or not available: %1 Parameters: %1 = File name
112505 Error when interpreting the contour %1
112506 Maximum number of contour elements exceeded %1
112541 Program cannot be interpreted
112604 Connection to the PLC broken off
112605 Asynchronous subroutine was not executed
112650 Unknown PLC error
112999 Faulty grafic data. Exit graphic and restart
120000 Area %1 cannot be loaded! Acknowledge alarm, press area switchover key!
120001 Area %1 cannot be selected. Please deactivate area %2
120002 Area %1 is still active. Please deactivate area %1
120003 Area %1 cannot be deactivated. Please try again
120005 Please acknowledge the dialog box in area %1
120006 The channel switchover is currently disabled by area %1.
120007 The channel switchover is currently disabled.
120008 Control unit switchover, PLC timeout: 001 control unit switchover, PLC timeout: 002 control unit switchover, PLC timeout: 003
120120 The alarm list is full of alarm texts: Number of alarm texts too high Alarm texts: File %1 not found alarm texts: Input/Output error in file %1 alarm texts: Input/Output error alarm texts: Error when reading from the index file alarm texts: Error when writing in the index file alarm texts: Syntax error in alarm text file %1
120200 Image preparation suppressed
120201 Communication failure
120202 Waiting for a connection to the NC
120301 Faulty entry for hardkey ‘Program’ in Keys.ini.
120302 The selection is not possible. A program has to have been edited first via the area ‘Program’.
120303 The selection is not possible. The edited file %1 no longer exists.
120304 The selection is not possible. The file %1 has insufficient read rights.
120305 Selection is not possible. The file %1 is currently being edited.
120306 The selection is not possible. The file %1 is selected and active in channel %2.
120307 The file %1 cannot be opened for the editor because it is selected in channel %2 for execution from external sources.
120308 In the event of an emergency stop, the program %1 can only be changed in the machine/program correction area.
120309 The selection is not possible. Please close the simulation and repeat the selection.
120310 The selection is not possible. Please wait for the pending action or terminate it, then repeat the selection.
300000 Hardware drive bus: DCM not present
300001 Axis %1 drive number %2 not possible
300002 Axis %1 drive number %2 assigned twice
300003 Axis %1 drive %2 wrong module type %3
300004 Axis %1 drive %2 wrong drive type %3 (FDD/MSD)
300005 At least one module found on drive bus that has not been configured
300006 Module with drive number %1 has not been found on drive bus
300007 Axis %1 drive %2 not present or inactive
300008 Axis %1 drive %2 measuring circuit %3 is not available
